background image

Sanus Systems  2221 Hwy 36 West, St Paul, MN  55113  USA •  (6901-100015 <01>)

USA Customer Service: 1-800-359-5520 • [email protected] • www.sanus.com

Thank you for choosing the Sanus Systems VisionMount™ VMDD26. It mounts most flat panel televisions up to 1600 cm (63 in), 
tilts the TV +5° to -15°, swivels ± 75°, rolls ± 6°, and extends 654 mm (25.75 in) from the wall. 

WARNING

Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may 
cause property damage or personal injury. If you do not understand these directions, or have doubts about the 
safety of the installation, contact Sanus Systems Customer Service or call a qualified contractor. Sanus Systems is 
not liable for damage or injury caused by incorrect mounting, assembly, or use.

The TV must not exceed 79.4 kg (175 lb) or 1600 cm (63 in). The wall must support five times the weight of the TV 
plus the wall mount. If necessary, reinforce the structure before installing the unit. Failure to provide adequate 
structural strength may result in serious personal injury or damage to equipment.

The supplied wall mounting hardware is not for metal stud, concrete, brick, or block walls. If you are uncertain 
about the nature of your wall, consult an installation contractor. The installer must verify the safety of any 
installation method or use of hardware not provided by or recommended by Sanus Systems.

VMDD26

3/16 in

Supplied Parts and Hardware

Make sure all parts are included and undamaged. Never use defective parts. If hardware is damaged or missing, contact your local 
hardware store or Sanus Systems. Before returning products to the point of purchase, contact Sanus Systems. Replacement parts 
for products purchased through authorized dealers are shipped directly to you.

[01] x 1

[04] x 2

[05] x 2

[06] x 4

[02] x 1

[03] x 2

Содержание VisionMount VMDD26









Отзывы: