background image

Assembly Instructions for Model: VMPR1

Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method 

of ceiling mounting inverted LCD/DLP projectors. Its low profile design offers roll, pitch, and yaw adjustment. The VMPR1 steel-to-steel 

construction with adjustable height to maintain proper ventilation, hold registration for quick lamp changes and easy filter cleaning without 

loosing registration. The VMPR1 ceiling mount includes an NPT Extension Pipe that may be used where more room is required, such as 
areas with vaulted or cathedral ceilings.

   WARNING: 

The maximum weight to be installed on the VMPR1 ceiling mount is 50 pounds [22.68 Kg].  Improper installation may result in 

serious personal injury. Make sure the structural members can support a redundant weight factor five times the total weight 

of the equipment. If the structure can not support this weight, reinforce the structure prior to installing the VMPR1.

If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or 

contact  Sanus  at  800.359.5520  or  www.sanus.com.  Check  carefully  to  make  sure  that  there  are  no  missing  or  defective  parts.  Our 
customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts 
for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Do not use this product 

for any purpose that is not explicitly specified by Sanus Systems. Please call Sanus Systems before returning products to the point of 

purchase.

Required Tools: 

Open End Wrenches, Phillips screwdrivers, Allen Wrenches (provided), other tools may be required depending on the 

method of installation.

Supplied Parts and Hardware: 

(All threaded fasteners are shown full size.)

Sanus Systems 

 2221 Hwy 36 West, Saint Paul, MN 55113  11.09.06 (6901-100023)

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Universal Projector Interface - A

Qty. 1

Extension Arm - B

Qty. 2

Ceiling Plate - C

Qty. 1

Adjustment Bracket - D

Qty. 1

Bottom Cover - G

Qty. 1

Top Cover - H

Qty. 1

NPT Extension Pipe - F

Qty. 1

NPT Adapter - E

Qty. 1

Содержание VMPR1









Отзывы: