18
Press
PAUSE
during playback.
Press
SLOW
one by one: The picture advances frame by
frame.
To return to playback: Press
PLAY
or
PAUSE
.
Frame by Frame picture
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion, press
the
TR
or
–
to reduce the noise bars.
If the still picture jitters excessively, press
TR
or
–
to stabilize the still picture.
Repeat playback
The entire video tape will be played until its end. The tape will
then automatically rewind to the beginning and the playback
will be repeated.
1
Press
VCR MENU
. Press
SET +
or
–
to select AUTO
REPEAT.
3
Press
VCR MENU
until the menu screen is cleared.
if you press
CALL,
“
” will appear on the screen.
Then press
ENTER
to se-
lect “ON” or “OFF”.
If “ON” is selected, the play-
back will be repeated end-
lessly.
4
To start the playback, press
PLAY
.
The playback will be repeated endlessly.
2
To cancel repeat mode
:
Follow the above step
1
, then press
ENTER
to select the
OFF position. Press
VCR MENU
to return to the TV.
Press
CALL
.
The counter display shows the tape
running time during playback or re-
cording.
This function makes tape-rewinding stop at the counter
00:00:00 position automatically.
NOTES for Counter Display:
If you rewind the tape beyond “00:00:00”, a minus sign
(“–”) will be displayed in front of the time.
When you load a tape, the counter will reset to “00:00:00”.
The counter does not function on nonrecorded (blank) sec-
tions of the tape. When you rewind, fast forward or play tapes
through blank sections, the counter stops.
•
•
•
Press
COUNTER RESET
at the
desired tape position. The counter
display will be reset to the
“00:00:00” position (e.g. the begin-
ning of recording).
2
Press
STOP
when playback or recording is finished.
Press
ZERO RETURN
.
The tape will be rewinded or fast forwarded and automati-
cally stop at the “00:00:00” position.
The CLOCK/COUNTER-button
Press
CLOCK/COUNTER
. The clock and tape counter alter-
nate with each other in the display.
1
3
Video index search system
This function enables you to locate the beginning of any
recording made on the VCR.
Recording an INDEX MARK
The Index Search function automatically records an INDEX
mark on the tape whenever a recording is initiated.
Index Search
Press
INDEX
or during stop or play mode.
For Succeeding programs: Press
INDEX
.
For Preceding programs: Press
INDEX
.
(Additional press increases the INDEX NO. up to 9.)
When the
INDEX
or is pressed, the unit starts
searching the INDEX NO. selected and finds the portion,
then playback starts automatically.
To stop the Index Search, press
STOP
.
NOTES for Video index search system:
When you record an INDEX mark at the very beginning of the
tape, the mark may not be found.
During INDEX search, the tape may stop and begin to play
at a slightly different location.
INDEX may not function properly with old or worn out video
tapes.
INDEX marks may not be found if it is extremely close to the
point where the search began.
In recording, if you stop recording temporarily, the INDEX
mark is not recorded on the tape.
•
•
•
•
•
MENU
TIMER REC SET
AUTO REPEAT
ON
OFF
ON
OFF
SAP
CH SETUP
SYSTEM SETUP
VCR
VCR
NOTES:
• The audio output is muted during SPEED SEARCH, STILL,
FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars which are
caused by the system.
• The Special Playback will automatically change to playback
after approx. 5 minutes to protect the video tape against
excessive wear.
Adjusting tracking condition
Whenever you insert a tape and start playback, automatic
tracking starts working and continuously analyzes the signal
to enable optimum picture quality during playback.
Automatic tracking adjustment
ZERO RETURN function
Slow Motion
During playback press
SLOW
.
To return to playback: Press
PLAY
or
SLOW
.
2D80401A[E](18-23)
4/27/04, 1:35 PM
18
