Sansui DTV2750, Руководство пользователя

Страница: 7 / 36

7
Remote control
the display from the screen, press this button again. This
button is also the “–” button used when selecting digital
channels.
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button. The clock will
count up 10 minutes each time the button is pressed in the
order of 0, 10, 20, ...100, 110, 120. After the sleep time is
programmed, the display will disappear then reappear
momentarily every ten minutes to remind you the sleep timer
function is operating. To confirm the sleep time setting,
press the SLEEP button once and the remaining time will
be momentarily displayed. To cancel sleep time, press the
SLEEP button repeatedly until the display turns to 0.
5. VOL (VOLUME) + / – Buttons - Press the + button to
increase, or the “–” button to decrease the volume level.
Use to select the desired setting during the menu screen
operation.
6. MENU/ENTER Button - Press to display the menu screen.
While in the on-screen menu, press to enter or select
options.
7. EXIT Button -
Press to exit the menu screen.
8. TV/AV Button - Press this button to display SOURCE
SELECTION menu to select the video input source.
9. QUICK VIEW Button - This button allows you to go back to
the previous channel selected by pressing the QUICK VIEW
button. Press this button again to return to the channel you
were watching.
10. MUTE Button - To turn off the sound, press this button once.
The TV will be silenced and the symbol “MUTE” will appear
on the screen. The muting feature can be released by pressing
the MUTE button again or one of the VOL + or – buttons.
11. CH (CHANNEL) / Buttons - Press the button to
change to a higher numbered channel set into memory.
Press the button to change to a lower numbered channel
set into memory. Use to select the desired setting during
the menu screen operation.
12. PICTURE SIZE Button - Press to change the picture size.
13. AUDIO Button - Press to select the desired audio setting.
14. CLOSED CAPTION Button - Press this button to display
CLOSED CAPTION menu.
15. ANALOG/DIGITAL Button - Press to select analog/digital mode.
1. POWER Button - Press to turn the power on/off to the TV.
2. Direct Channel Selection Buttons (0-9) - Allow direct
access to any channel.
3. –/DISPLAY Button - When the TV is receiving an analog
signal pressing this button will display the current
information on-screen. When the TV is receiving a
digital signal, pressing this button once will display the
digital information on-screen; pressing it a second time
will display the analog information on-screen. To remove
Before using the remote control, batteries must first be installed.
HOW TO INSTALL BATTERIES
1. Open the battery compartment cover.
2. Install two “AAA” batteries (not supplied).
3. Replace the battery compartment cover.
Use two “AAA” size batteries (not supplied). The batteries
may last approximately one year depending on how much
the remote control is used. For best performance, it is
recommended that batteries should be replaced on a yearly
basis, or when the remote operation becomes erratic. Do not
mix old and new batteries or different types.
BATTERY PRECAUTIONS
These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline
and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not try to recharge batteries not intended to be recharged;
they can overheat and rupture (follow battery manufacturer’s
directions).
9
1
2
3
4
5
6
7
8
10
12
11
13
14
15
J30K0901B_EN.indb 7 8/23/07 3:55:07 PM