SANRAD I3.1.1205 Скачать руководство пользователя страница 56

Страница: 56 / 348

4-4

SANRAD V-Switch CLI User Manual

Initial V-Switch Configuration

The V-Switch has a default IP Address of 10.11.12.123. This allows you to set
initial startup parameters via a telnet session.

Assigning a Management IP Address

Mgnt port is only for

V-Switch 3000.

The management IP address can be set via:

RS-232 port

Telnet session

LCD Buttons (only for V-Switch 3000)

Telnet/SSH Connection

To initialize the V-Switch via telnet/SSH session:

Change your computer’s IP Address to anything on the same subnet
10.11.12.*

Connect to the management port on the V-Switch.

Telnet to 10.11.12.123.

Enter Username and Password:

sanrad.

You will be asked to accept or change the default values for :

Set the default IP Address.

Set the default IP Mask.

Set the default V-Switch name.

Set the default management port (Mgnt or ETH1).

Содержание I3.1.1205





























































































































































































































































































































































Результаты поиска

Содержание I3.1.1205

Отзывы:

SANRAD I3.1.1205, Руководство пользователя, Страница: 56 / 348

Результаты поиска

Содержание I3.1.1205

Отзывы: