S&P TEMPEST HVLS Скачать руководство пользователя | Manualshive

Страница: 26 / 40

background image

26

8

INSTALLING BLADES

Bolt a. M8-35 Soc Cap must be installed on the inner section of the blade.
Bolt b. M8-25 Soc Cap must be installed on the outer section of the blade.
Each bolt requires one (1) c. M8 Zinc Split Lock washer.

Blade Hardware Kit (supplied):

a. (6) Soc Cap 5/16-18 x 5/8
b. (6) Soc Cap 5/16-18 x 3/4
c. (12) Zinc Split Lock Washer 5/16

Top of Blade

To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

Pour réduire le risque de blessure, ne pas plier les crochets lame lors de l’installation les crochets, l’équilibre entre les
lames, ou de nettoyer la ventilateur. Ne pas insérer d’objets étrangers entre les pales du ventilateur.

WARNING/ AVERTISSEMENT

a

b

c

«
...
24
25
26
27
28
...
»

Содержание TEMPEST HVLS









































Отзывы:

Нет отзывов

Похожие инструкции для TEMPEST HVLS

Бренд: Lasko Страницы: 6

Бренд: Vallox Страницы: 13

Бренд: Quirky Страницы: 18

Бренд: KDK Страницы: 20

Бренд: RAMTONS Страницы: 4

Бренд: KALE FANS Страницы: 15

Бренд: KORADO Страницы: 72

Бренд: ebm-papst Страницы: 11

Бренд: Valueline Страницы: 28

Бренд: Maico Страницы: 28

Бренд: Parrot Uncle Страницы: 4

Бренд: Ragalta Страницы: 10

Бренд: ebm-papst Страницы: 12

Бренд: elix BELGIUM Страницы: 17

Fantech HERO 200H

Бренд: SystemAir Страницы: 32

Бренд: Faro Barcelona Страницы: 20

Louvre FP1320 Series

Бренд: Fanimation Страницы: 16

Бренд: Caframo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды