background image

4    S&C Instruction Sheet 1074-510

Safety Information

Understanding 
Safety-Alert Messages

There are several types of safety-alert messages which may appear throughout this 
instruction sheet as well as on labels attached to the SpeedNet ME Radio. Familiarize 
yourself with these types of messages and the importance of the various signal words, 
as explained below.

 

DANGER

“DANGER” identifies the most serious and immediate hazards that 

will

 likely result in 

serious personal injury or death if instructions, including recommended precautions, 
are not followed .

 

WARNING

“WARNING” identifies hazards or unsafe practices that 

can

 result in serious personal 

injury or death if instructions, including recommended precautions, are not followed .

 

CAUTION

“CAUTION” identifies hazards or unsafe practices that 

can

 result in minor personal 

injury if instructions, including recommended precautions, are not followed .

NOTICE

“NOTICE” identifies important procedures or requirements that 

can

 result in product 

or property damage if instructions are not followed .

Following Safety 
Instructions

If you do not understand any portion of this instruction sheet and need assistance,  
contact your nearest S&C Sales Office or S&C Authorized Distributor. Their telephone 
numbers are listed on S&C’s website 

sandc.com

. Or call S&C Headquarters at  

(773) 338-1000; in Canada, call S&C Electric Canada Ltd. at (416) 249-9171.

NOTICE

Read this instruction sheet thoroughly 
and carefully before installing or operating 
your S&C SpeedNet ME Radio .

Replacement 
Instructions and 
Labels

If you need additional copies of this instruction sheet, contact your nearest S&C Sales 
Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

It is important that any missing, damaged, or faded labels on the equipment be replaced 

immediately. Replacement labels are available by contacting your nearest S&C Sales 
Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

Содержание SpeedNet ME

















Отзывы: