background image

3

INSTALLATION

ENVIRONMENT
Leave some space

Space at last 15cm between the washer and the wall.

Place the washer on a sturdy flat surface.

If the washer is placed on an uneven or weak 
surface, noise or vibration may be occured.
(Allowable is 2°)

Never install the washer near water.

Do not place the washer in steamy rooms or where 
the washer is directly exposed to rain.
Moisture may destroy the electrical insulation and 
cause an electrical shock hazard.

Avoid direct sunlight or heating devices.

As plastic and electrical components are affected 
by direct heat, never place the washer near heaters, 
boilers,etc.
Do not place under direct sunlight.

HOW TO CLEAN THE FILTER 

(In case drain pump)

1.  Place a rag under the washer filter not to wet the 

floor.

2.  Rotate the filter counterclockwise and pull out 

the filter.

3.  Remove dirts and rotate the filter clockwise until 

it locks in position.

Remark : Should be 
cleaned Filter at least 
1 time a week.

CONNECTING THE DRAIN HOSE

Insert the drain hose(a) and push it tighly to be 
connected as arrow direction.

Install the drain hose about 70~80cm above the 
ground for pump model.

CLEANING THE MACHINE

CLENING THE LINT FILTER

If the dregs are filled up in the lint filter after finishing 
the wash, push down(1) and pull it out(2) as shown in 
figure.
Remove the collected lint and rinse the filter net.

OVERFLOW FILTER

Pull the upper side of the overflow filter with 
two fingers into the hole ‘A’ in the direction of 
arrow as shown in the figure.

CLEANING THE COVER WINDOW SPIN

1.  Rotate the cover window spin clockwise 

and pull out.

2.  Cleaning the cover window spin.
3.  Insert the cover window spin back and 

rotate it counterclockwise until locks in 
positon.

Remark : Should be cleaned the cover window 

spin at least 1 time a month.

CLEANING THE WASH TUB

Wipe off strains on the cabinet and operation panel 
with soft cloth.
Do not use benzene, thinners, cleanser, or wax, nor 
scrub the washer with a brush.
Painted surfaces or plastic parts will be damaged.

Filter

Close

Rag

Open

(WITHOUT PUMP)

70~80cm

Lint Filter

Cover Window Spin

Close

Open

WT80J7-02206F_EN.indd   3

2006-06-17   ¿ÀÈÄ 3:59:33

Содержание WT80J7









Отзывы: