Samsung WIP-500M Скачать руководство пользователя

Страница: 41 / 49

PHONE SETTINGS

Press the

[MENU]

button in idle mode, and then select the

[5. Phone

Settings]

icon. The submenus are not displayed until a password is entered.

Editing Name

This function enables you to enter random characters on the screen displayed on
the initial screen.

•

Refer to ‘Entering Characters’ section in ‘Basic Features’ of this guide for enter-
ing characters.

Display

This function enables you to select the background of the initial screen that
appears when power on.

Ring Volume

This function enables you to adjust the bell volume.

Warning

This function enables you to hear a warning tone when you move to a shadow
zone during a call.

[MENU]

4. Volume/Ring

[OK]

3. Ring Volume

[OK]

(Select Bell Volume)

[OK]

You can adjust the volume of the bell by using the

[Volume]

button.

[MENU]

4. Volume/Ring

[OK]

4. Warning

[OK]

(Select On/Off)

[OK]

[MENU]

5. Phone Settings

[OK]

Enter a Password

1. Edit Name

[OK]

Enter your Name

[OK]

If you save your name in your phone, your name will be displayed on
the other party’s phone when you are connected to another party
(intercom user). (This applies only when your phone number is not
saved in the phone book of the intercom user.)

[MENU]

5. Phone Settings

[OK]

Enter a Password

2. Display

[OK]

(Select a Screen)

[OK]

Home Page

Table of Contents

WIP-5000M Guide

Содержание WIP-500M


















































Результаты поиска

Содержание WIP-500M

Отзывы:

Похожие инструкции для WIP-500M

Бренды по названию

Популярные бренды

Samsung WIP-500M, Руководство пользователя

Результаты поиска

Содержание WIP-500M

Отзывы:

Похожие инструкции для WIP-500M

Бренды по названию

Популярные бренды