Samsung WIDA10 Скачать руководство пользователя страница 6

Version 1.0

 

Samsung Electronics

page 6 of 8

 

 

 

 
 

IMPORTANT NOTE:

 

 

FCC Radiation Exposure Statement:

 

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 20cm 

between the radiator & your body. 

 

 

IMPORTANT NOTE:

 

 

This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC 

 

compliance requirement of the end product, which integrates this module. 

 

20cm minimum distance has to be able to be maintained between the antenna and the users for 

the host this module is integrated into. Under such configuration, the FCC radiation exposure 

limits set forth for a population/uncontrolled environment can be satisfied. 

Any changes or modifications not expressly approved by the manufacturer could void the user's 

authority to operate this equipment. 

 

 

USERS MANUAL OF THE END PRODUCT:

 

 

In the users manual of the end product, the end user has to be informed to keep at least 20cm 

separation with the antenna while this end product is installed and operated. The end user has to 

be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment 

can be satisfied. The end user has to also be informed that any changes or modifications not 

expressly approved by the manufacturer could void the user's authority to operate this equipment. 

If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is 

required to be available in the users manual: This device complies with Part 15 of FCC rules. 

Operation is subject to the following two conditions: (1) this device may not cause harmful 

interference and (2) this device must accept any interference received, including interference that 

may cause undesired operation. 

Содержание WIDA10









Отзывы: