Samsung WF306BAW/XAA Скачать руководство пользователя страница 7

Страница: 7 / 89

1-4

■ How to Level the Unit

1.Select an installation place.
► Install the unit with 10cm or more
clearance from its surrounding walls.

2.Check if the unit is leveled.
► If the unit wabbles, adjust the leveling
legs.

3.Adjust the leveling legs.

1-2. Precautions upon Installation

► The 4 leveling legs should

touch the ﬂoor all together.

When the unit is not leveled

► Lift up the unit a little bit and adjust the shortest.
► Turn the leveling bolt counter clockwise as shown

in the picture above (The leveling leg gets longer.)

► Slide your Washer into

position.

► Level your Washer by

turning the leveling legs

in or out as necessary

by hand. When your

Washer is level, tighten

the nuts using

the wrench included

with your Washer.

► If you install your washer on

softﬂoor, you should place the

rubber cup under adjustable

eg. Before put rubber cup, please

remove ﬁlm for double-side tape

attached on rubber cup.

Содержание WF306BAW/XAA


























































































Результаты поиска

Содержание WF306BAW/XAA

Отзывы:

Похожие инструкции для WF306BAW/XAA

Бренды по названию

Популярные бренды

Samsung WF306BAW/XAA, Руководство по обслуживанию

Результаты поиска

Содержание WF306BAW/XAA

Отзывы:

Похожие инструкции для WF306BAW/XAA

Бренды по названию

Популярные бренды