background image

7

M a i n t e n a n c e

Clearing Blockages

Disconnect cleaner from electrical outlet.

The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can
sometimes become clogged.  If you notice a change in the sound of the vacuum motor, check for blockages.

Remove the Hose and
disconnect the Wand.
Check for clogs in the vacuum
base, the wand, the hose and
the suction inlet.

If the blockage persists, turn
the vacuum cleaner off and
unplug it. Remove the bottom
plate. Lift up the short hose in
the base of the vacuum.
Inspect the hose for clogs and
remove any obstructions.
Replace the short nozzle hose
and the bottom plate.

Remove Dirt Cup and check
Upper Tank and Louvers.
Check to make sure Louvers
are Installed correctly. To
unlock the Louvers, grasp the
rim and turn Toward the left.
Pull straight down to remove. If
the Louvers are missing or not
locked into place, check and
clear the tube in the center of
the Dirt Cup.

Brush bar Replacement

Remove the tool from the hose,
and turn upside down. Slide the 
switch to unlock position.

Remove bottom plate.
And remove brushbar and
discard.
Inspect belt to ensure that it is in
good condition. If broken or
cracked, please replace. (See
below for details.)

With the curved ends facing
down, slide end plates of
brushbar into slots on the tool.
To replace bottom plate, insert
the four tabs on edge of
bottom plate into slots on front
of tool. Pivot bottom plate
down and snap closed.

3-14

3-16

3-15

Use for upholstered furniture, carpeted stairs and hard-to-reach places.

3-17

3-18

3-19

Mini Turbo Brush

3-20

3-21

3-22

Belt Replacement

Grasp turbine and pull firmly to
remove.
Remove belt from turbine pulley.
Replace with new belt.

With flat sides of turbine
retainers pointing down, slide
retainers into grooves in tool
housing and snap into place.
Replace brushbar and bottom
plate.

Cleaning Brushbar

• Cut off pet hairs or threads
surrounding brush by using
scissors.

DJ68-00294G(0.0)  2007.5.15 4:45 PM  페이지8    in

Содержание SU-2930 Series













Отзывы: