Samsung SpinPoint M8 Скачать руководство пользователя

Страница: 59 / 83

Spinpoint M8 Product Manual REV 2.7

Word

Content

Description

1=Media Card Pass Through command feature set supported

1=Media serial number supported

1=SMART self-test supported

1=SMART error logging supported

7469h

Command set/feature enabled. (The default manufacturing setting is as below)

Obsolete

1=NOP command enabled

1=READ BUFFER command enabled

1=WRITE BUFFER command enabled

Obsolete

1=Host Protected Area feature set enabled

1=DEVICE RESET command enabled

1=SERVICE interrupt enabled

1=Release interrupt enabled

Loo

k-ahead enabled

1=Write cache enabled

1=PACKET Command feature set enabled (Should be cleared to 0)

1=Power Management feature set enabled

1=Removable Media feature set enabled

1=Security Mode feature set enabled

1=SMART feature set enabled

BC41h

Command set/feature enabled.

15-14

Reserved

1=FLUSH CACHE EXT command supported

1=FLUSH CACHE command supported

1=Device Configuration Overlay features supported

1=48 bit address feature supported

Reserved

1=SET MAX security feature enabled by SET MAX SET PASSWORD

1=Set Address Offset Reserved Area Boot, INCITS TR27:2001

1= SET FEATURES subcommand required to spin-up after power-up.

1=Power-Up Standby feature set enabled

1=Removable media status notification feature set enabled

1=Advanced Power Management feature set enabled

1=CFA feature set enabled

1=READ/WRITE DMA QUEUED supported

1=DOWNLOAD MICROCODE command supported

6123h

Command set/feature default.

Shall be set to 0

Shall be set to 1

1=IDLE IMMEDIATE with UNLOAD FEATURE supported

Reserved for technical report

1=URG bit supported for WRITE STREAM DMA EXT and WRITE STREAM

EXT

1=URG bit supported for READ STREAM DMA EXT and READ STREAM

EXT

64-bit World wide name supported

1=WRITE DMA QUEUED FUA EXT command supported

1=WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT command

supported

General Purpose logging feature set supported

1=Valid CONFIGURATION STREAM command has been executed

1=Media Card Pass Through command feature set enabled

1=Media serial number is valid

1=SMART self-test supported

1=SMART error logging supported

Содержание SpinPoint M8




















































































Результаты поиска

Содержание SpinPoint M8

Отзывы:

Похожие инструкции для SpinPoint M8

Бренды по названию

Популярные бренды

Samsung SpinPoint M8, Руководство по эксплуатации продукта

Результаты поиска

Содержание SpinPoint M8

Отзывы:

Похожие инструкции для SpinPoint M8

Бренды по названию

Популярные бренды