System Requirements
Installing the CD-R/RW Drive
Installing the Device Driver
4
5
Before you install the CD-R/RW drive, we strongly recommend that you make certain
that your set-up meets the system requirements listed below.
Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close
button is on the right.
1
Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the CD-R/RW drive.
To install the drive, proceed as follows.
2
Remove the cover of your PC(main unit of the computer).
3
Remove the blank cover panel of the 5.25 inch unit in
which the CD-R/RW drive is to be installed.
4
Connect the CD-R/RW drive to the IDE interface and
power cables located inside your computer.
☛
Connectors are keyed so it is impossible to put them in
☛
an incorrect position. Do not force the connectors, if they
☛
do not seem to fit.
5
Install the CD-R/RW drive into the unit and secure it with
mounting screws (recommended standard M3x6).
☛ ◆
Depending on your PC model, you may need to attach
☛ ◆
guide rails to the drive, so that the drive is held firmly in place.
☛ ◆
On the ground that the guide rails are parts of the computer,
☛ ◆
if you don’t have these, please purchase separately.
☛
◆
If you use screws that are longer than the recommended
☛ ◆
standard, you may damage the drive.
6
Put the cover back on your PC.
Item
Description
Type of computer
Pentium 75MHz(or higher) with an IDE interface
16MB RAM(or higher)
528MB higher(Transfer Rate 800KB/sec higher Access,
Time 20m/sec Lower)
5.0(or higher)
TIP:For MS-DOS, The CD-R/RW drive can only Read a
disc without Premaster Software
RAM
Hard drive
MS-DOS
Microsoft
®
Windows 95
®
or Windows NT 4.0
®
TIP:For Windows NT
®
, we recommend Service Pack2,
Version 4.00.1381.
Windows
You can install the device driver for DOS or for Windows.
TIP : You can use the CD-R/RW drive to only read a disc in DOS/Windows 3.1.
1
Turn on your computer and wait for it to boot.
7
Reboot your system.
Result:
◆
The computer restarts
◆
Both the device driver and MSCDEX are loaded.
6
When the Setup Completed screen is displayed, remove the installation
floppy disk from the drive.
2
Insert the driver disk into a floppy disk drive (usually the A drive).
4
Run the CDSETUP program:
5
To...
Then enter...
Confirm the installation Y
Exit without installing N
Result:
If you answer Y(Yes), the installation program automatically
◆
Creates a SAMSUNG directory on your hard disk
◆
Copies the required softwares (mscdex.exe and sscdrom.sys)
◆
Modifies the CONFIG.SYS and AUTOEXEC.BAT files
3
If you are a...
Then...
DOS user
Windows user
3.1
Windows 95 user
/NT 4.0
◆
Type a: at the DOS prompt.
◆
Press the RETURN key.
◆
Access the File Manager.
◆
Click on the A icon.
◆
When you are in Windows 95, it is not
◆
necessary to install Device Driver.
◆
Whereas, when you are in Dos Mode of
◆
Windows 95, then install as follows.
◆
Click on MY COMPUTER icon.
◆
Click on the A icon.
If you are a...
Then...
DOS user
Windows user
3.1
◆
Type CDSETUP after the a: prompt.
◆
Press RETURN.
Double-click CDSETUP.EXE from the
Windows File Manager.
English
SCW-230(E/G/F/S) 3/31/00 2:35 PM Page 3