Samsung SC-148A Скачать руководство пользователя страница 15

Страница: 15 / 15

Specifications

SAMSUNG

continually strives to improve its products. Both the design specifications and these user

instructions are thus subject to change without notice.

Technical Specifications

ITEM

Model Name

SC-1

Disc

Disc types supported in
read mode

CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1, Form-2,
Photo-CD(Single, Multi-session), Video CD ready, CD-Plus, CD-Extra,
Enhanced CD, CDI/FMV, CD-R/RW

Disc diameter

120mm or 80mm

DRIVE PERFORMANCE

Data transfer rate

X / Max. 7800KB/s

PIO Mode 4, DMA MW2, Ultra DMA (Option)

ACCESS TIME(typical)

ms(typical)

Data Buffer capacity

128KB

Laser

Semiconductor laser

Slide mechanism

Gear motor

Spindle motor

Brushless motor

Load mechanism

Tray, DC motor(Soft Eject)

ERROR RATE

Mode-1 : 1block / 10

bits, Mode-2 : 1block / 10

bits

FRONT PANEL

Eject button

Auto eject or Auto inject

Indicator(LED)

POWER ON/BUSY

Headphone output

Stereo mini-jack (Ø3.6mm) 0.60 ± 20%(Vrms) 33 ohm

Volume control

Wheel type

REAR PANEL

Required power

+5VDC, 1.3A, +12VDC, 1.5A

Interface connector

ATAPI

Audio output

Line out 0.7 ± 20%(Vrms) : 47Kohm

Jumper block

Molex 70203 or other compatible models

OPERATING ENVIRONMENT

Operations

Temperature: 5~45°C Humidity: 10~80%

Storage

Temperature: -25~60°C Humidity: 10~90%

GENERAL

Dimensions

148.2(W) x 42(H) x 184(D)mm

Net weight

740g (set only)

RELIABILITY

MTBF

125,000 POH(Duty 20%)

Содержание SC-148A
















Результаты поиска

Содержание SC-148A

Отзывы:

Похожие инструкции для SC-148A

Бренды по названию

Популярные бренды

Samsung SC-148A, Руководство пользователя

Результаты поиска

Содержание SC-148A

Отзывы:

Похожие инструкции для SC-148A

Бренды по названию

Популярные бренды