Samsung SC-140 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 51

background image

1

Specifications

1. General Specifications

- Drive type : Computer built-in

- Power consumption : DC + 5V, 1.7A

DC + 12V, 1.0A

- Dimensions : 149mm(W)X41.5mm(H)X202.6mm(L)

- Net Weight : 950g

2. Electrical Features

- Interface : ATAPI BUS(IDE)

- Data transfer rate 6000KByte/Sec MAX

(3100KByte/Sec AVG.)

- ACCESS TIME : 1/3 stroke : Below 120msec

full stroke : Below 190msec

- Buffer Capacity : 128Kbyte

- Error ratio : Mode 1: Below 10

-12

Mode 2: Below 10

-9

- Frequency response : 20Hz~20KHz (Limeout)

100Hz~20KHz (H/pout)

- Signal to noise ratio : 75dB(1KHz, Limeout)

65dB(1KHz, H/pout)

- Distortion factor : 0.15% Less than(1KHz)

- Channel separation : 65dB(1KHz, Limeout)

55dB(1KHz, H/pout)

- Signal output level : LINEOUT : 0.7 Vrms(

±

20%)

H/PHONE : 0.6 Vrms(

±

20%)

- Used laser : Semiconductor laser

2. Earthing cautions at handling Pick-up

- Because the laser diode in optical Pick-up is subject

to get out of order due to the potential difference
occurring by electricity load charged in clothes or
bodies, observe the following earthing items at
handling.

1) Body earthing(hand) : Be sure to wear a wrist strip

with one side earthed.(Impedance : Below 104).
It removes the electricity formed in body.

2) Work table earthing : Put the earthed conductive

plate(Impedance : Below 104) such as copper plate

on work table.

3) Cautions for clothes : Do not have any clothes

touch with Pick-up because the electricity formed in
clothes is destroyed easily.

Cautions at Service

1. General Items

1) Be careful not to have your eyes or a part of body

touch with laser diode at repair because this
product uses laser diode.

2) Do not disassemble Pick-up at repair. If the laser

diode is bad, replace the entire Pick-up.

3) Keep away from TV or other electrical units at

repair to prevent influence from surrounding units.

4) If you replace the parts during repair, be sure to

unplug the power cable before replacement.

5) If you insert a disc into the drive, be sure to load it

correctly.

6) Because this unit can't be used by itself, surely

mount it on PC (486 DMA support) and check the
operations in use of private device driver floppy
diskette. Refer to Instruction manual.

7)This unit has many parts with features related to

safety and especially, for essential parts, the
importance is indicated on circuit diagram and
part list.
Be certain to use the parts with same specifications
at replacing these parts.

SCR-140(A4)-en 99.3.15 8:30 AM ˘

`

1

«
...
2
3
4
5
6
...
»

Содержание SC-140




















































Отзывы:

Нет отзывов

Похожие инструкции для SC-140

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 52

Бренд: Asus Страницы: 28

Бренд: Asus Страницы: 9

Бренд: Asus Страницы: 36

DVD Movie Writer

Бренд: HP Страницы: 24

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 4

Бренд: LG Страницы: 14

Бренд: LG Страницы: 1

Бренд: LG Страницы: 2

Бренд: LG Страницы: 4

Бренд: LG Страницы: 2

Бренд: LG Страницы: 4

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды