Samsung Potomac-PJT WF393 Скачать руководство пользователя страница 5

Страница: 5 / 40

- 5/39 -

Step 1

①

Check Tub for abnormal noise.

- Shake the Tub back and forth to check where the

noise is coming from.

②

Hanger Spring connection & Grease application

condition

- Check if grease is properly applied between
Hanger Spring and Hanger Guide friction part

Step 2

①

Check if Damper is separated or unassembled.

If the bolts connecting damper

- If the dampers are rusted or not fastening,

☞ replace.

②

Check the condition of loosening of Damper

connection.

- The shape of connected part of Bottom-Plate is

defective, and thus it does not rotate properly.

- It does not rotate properly because it was

connected too much in the assembling process.

☞ When it does not rotate properly, “Dda-dda-dda”

noise is generated due to friction between Damper &

Bottom-Plate. Thus, do as in ③.

③

What to do when Damper connection is

loosened.

- Add Nut M10.

- Product Name: Nut-Hexagon (6021-001588)

※ Damper connecting force : 250 ~ 350kgf.㎠

Check Point

Check the operating condition of Damper.

Tip 1-2. Damper & Hanger Abnormality

Содержание Potomac-PJT WF393









































Результаты поиска

Содержание Potomac-PJT WF393

Отзывы:

Бренды по названию

Популярные бренды

Samsung Potomac-PJT WF393, Руководство по ремонту

Результаты поиска

Содержание Potomac-PJT WF393

Отзывы:

Бренды по названию

Популярные бренды