Samsung NX15 Скачать руководство пользователя страница 211

Страница: 211 / 257

5-10

Manual

Traveling with the Computer

- When traveling, keep the system and the AC adapter disconnected. Otherwise,

it may affect the functions of the system.

- Make sure that the system is not pressed by a book or heavy objects. The LCD

may get damaged.

- When traveling by plane, use a bag designed for notebook PCs and hand-carry

the computer.

- Allow the computer and disks to pass through security X-rays but do not pass the

computer and disks through metal detectors.

- Do not use the computer during take off and landing.

Make sure the eject button of PCMCIA card slot is locked.

Содержание NX15


































































































































































































































































Результаты поиска

Содержание NX15

Отзывы:

Похожие инструкции для NX15

Бренды по названию

Популярные бренды

Samsung NX15, Руководство пользователя

Результаты поиска

Содержание NX15

Отзывы:

Похожие инструкции для NX15

Бренды по названию

Популярные бренды