Samsung MWR-WS00 Скачать руководство пользователя страница 8

Страница: 8 / 22

E-

Wired Remote Controller Error Codes

The error codes of the indoor and outdoor units are displayed

on the wired remote controller. Refer to the indoor and

outdoor unit technical manuals for the error codes reference.

The following error codes are related to the wired remote

controller.

Display

Explanation

Remark

601

Wired remote controller



indoor unit

communication error

602

Master



slave wired remote controller

communication error

When using 2 wired remote

controllers to control one indoor unit.

604

Wired remote controller tracking error.

No indoor units found.

606

COM1/COM2 installation error

653

Temperature sensor error

654

EEPROM error

Installing the Wired Remote Controller (Continued)

Connecting the Wired Remote Controller

Individual Control

 

Using one wired remote controller for one indoor unit.

Note

The wired remote controller can be only installed on COM2.

Outdoor unit

Indoor unit

COM1

COM2

COM1

COM2

Wired remote controller

MWR-WS00_E_IM_25180.indd 8

2006-03-28 ｿﾀﾈﾄ 3:13:38

Содержание MWR-WS00























Результаты поиска

Содержание MWR-WS00

Отзывы:

Похожие инструкции для MWR-WS00

Бренды по названию

Популярные бренды

Samsung MWR-WS00, Руководство по установке

Результаты поиска

Содержание MWR-WS00

Отзывы:

Похожие инструкции для MWR-WS00

Бренды по названию

Популярные бренды