background image

- 26 -

Symptom

Cause

Countermeasures

Strange popping 

sounds are produced 

while fish is cooked.

•  

Since fish is salty and 

maintains its mois-

ture, it is cooked while 

making a series of soft 

popping sounds. (The 

liquid may come out of 

the fish when the fish is 

cooked.)

•  

Food with bones such as fish (e.g. mackerel) and pork 

(e.g. pork chops) is cooked while making a series of 

soft popping sounds. Wrap the food completely so that 

food particles or spattered oils do not stick to the oven 

walls or floor.

Strange smell is pro-

duced in the oven.

•  

It may happen when 

food particles stuck to 

oven walls or floor.

•  

Clean the inside of the oven. => Remove strange smell 

through the Deodorant button => If the strange smell 

still remains, place a piece of lemon on the turntable 

and operate the oven for 5 minutes by pressing the 

Deodorant button.(However, the smells produced from 

the food exposed such as herbal remedies are not 

removed.)

Error

•  

Errors are classified into 

the case which is out 

of order and the case 

which is not out of order.

•  

Clean the inside of the oven. => Remove strange smell 

through the Deodorant button => If the strange smell 

still remains, place a piece of lemon on the turntable 

and operate the oven for 5 minutes by pressing the 

Deodorant button. (However, the smells produced 

from the food exposed such as herbal remedies are 

not removed.)

Accessory

•  

Visit the nearest Samsung Service Center or local 

dealer to buy accessories. Before visiting, check the 

model name printed on the lower right side of the front 

panel of the oven.

Number does not 

appear on the display 

screen.

It happens when the power 

saving function is acti-

vated.

•  

Since the government recommends the reduction of 

electricity, the power saving function is performed 

for number display like that power cord is unplugged 

when the oven is not used. (Numbers are displayed 

when another button is pressed or when the door 

opens.)

10-2 Customer inquiry cases and countermeasures (Continued)

Содержание MW1030WE































Отзывы: