Samsung ML-6050 Скачать руководство пользователя страница 51

Страница: 51 / 140

5-19

Samsung Electronics

Troubleshooting

Error code 1-100

Fault

Description

Partially blank image appears either periodically or non-periodically.

Partial blank image

Model ML-xxxx

Check

1. Transfer roller

2. Developer cartridge

Cause

1. The pressure force on the left and right transfer roller springs are not even, the springs are

damaged, the transfer roller is improperly installed, or the transfer roller bushing or holder is
damaged.

2. If a black image prints light or gradually light at intervals of 49 mm, the transfer roller is defective.

3. If there is a partial blank image on left and right side of the page:

1) The life of the transfer roller has expired.
2) Abnormal transfer voltage.
3) The life of the developer has expired.

Solution

1. Replace the defective components.

2. Replace the transfer roller.

3-1. Replace the transfer roller.

3-2. Measure the transfer voltage. If the voltage is abnormal, disassemble the main board and clean

the components stained with toner or paper particles.

3-3. Measure the weight of the developer. If the weight is less than 960 g ±20 g, replace the

developer.

Remark

Others

Содержание ML-6050













































































































































Результаты поиска

Содержание ML-6050

Отзывы:

Похожие инструкции для ML-6050

Бренды по названию

Популярные бренды

Samsung ML-6050, Руководство по обслуживанию

Результаты поиска

Содержание ML-6050

Отзывы:

Похожие инструкции для ML-6050

Бренды по названию

Популярные бренды