manualshive.com logo in svg

Samsung ML-2251N/XAA, Руководство по обслуживанию

Поделиться
Скачать
Samsung ML-2251N/XAA Скачать руководство пользователя страница 84

7-12

Troubleshooting

Samsung Electronics

Service Manual

7.3 Printer Faults – Causes and Solutions

7.3.1  All LEDs blinking (Fuser Error)

• Description

1. All the lamps on the operator panel blink.
2. The fuser drive gear breaks or melts.
3. When printing the motor skips or makes a noise due to a defective fuser drive gear

Check and Cause

Solution

Use EDC diagnostic code 10 to test the fuser. 
1. Thermostat, fuser power cable or heat lamp is open

circuit.

2. Thermistor is faulty.

3. Drive gear melted.

1. Replace heat lamp or cable harness if necessary.

Replace the whole fuser assembly if the 
thermostat is open circuit.

2. Carefully inspect the thermistor mounting. If the

mounting or the roller in this area is melted
replace the whole fuser assembly. If the thermistor
is faulty but there is no sign of heat damage
replace the thermistor sensor.

3. Replace the fuser.

7.3.2  All LEDs blinking (Scan Error)

• Description

All lamps on the OPE panel blink.

Check and Cause

Solution

Use EDC diagnostic code 05 to test the LSU.
1. LSU cable or connector faulty.

2. LSU motor is faulty.

3. Check the HSYNC signal.

Replace the LSU or cable harness as required.

Replace a main board if the same error persists after
replacing the LSU.

Содержание ML-2251N/XAA



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды