Samsung MH050FXCA2A Скачать руководство пользователя страница 99

Страница: 99 / 130

Samsung Electronics

9-8

Troubleshooting

●

If Error code is displayed on indoor or outdoor LED, check as follows;

- Manaul address setting

Step 1

Step 2

Contents

Turn on the system. But outdoor units PCB displayed E201 or E101 Error code.

Check point

Remarks

Check to Number of indoor unit’s SW01.

Outdoor PCB

SW01

Check to power cable to indoor units.

Check to communication cable indoor units.

Wire connect

Guidance

Step 1

Contents

Turn on the system. But outdoor units PCB displayed E203 Error code.

Check point

Remarks

Outdoor communication error between the outdoor main

PCB and sub PCB.

Outdoor PCB

SW01

Check to sub PCB wire and replace it.

Wire connect

Error code

E121

E122

E123

E154

Guicance

Contents

Turn on the indoor units. But indoor unit displayed E121/122/123/154 Error code.

Explanation

Indoor unit room temperature sensor error (open/short)

Indoor unit heat exchanger in temperature sensor error (open/short)

Indoor unit heat exchanger out temperature sensor error (open/short)

Indoor unite fan error

Please, all units turn off and check to indoor unit’s PCB and wire connection. E121/122/123 error detected, replace

related sensor.

Error code

E162

E163

Guidance

Contents

Turn on the system. But indoor unit displayed E162/163 Error code.

Explanation

Indoor unit EEPROM Error.

Indoor unit EEPROM Option Error.

Please, all units turn off and follow guidance.

E163 : Please reset indoor Option code.

E163 :

If you don’t know about that, replace indoor unit PCB which is related.

E162 : Please replace indoor unit PCB which is related.

Error code

E221

E237

E251

E320

Guidance

Contents

Turn on the system. But outdoor unit displayed E221/237/251/320 Error code.

Explanation

Outside temperature sensor error (open/short)

Indoor unit heat exchanger in temperature sensor error (open/short)

Condenser temperature sensor error (open/short)

Compressor Discharge temperature sensor error (open/short)

Compressor OLP sensor error (open/short)

Please, The System turn off and replace sensor which is related.

Содержание MH050FXCA2A



































































































































Результаты поиска

Содержание MH050FXCA2A

Отзывы:

Samsung MH050FXCA2A, Руководство по обслуживанию, Страница: 99 / 130

Результаты поиска

Содержание MH050FXCA2A

Отзывы: