Samsung MC17J8100CS/AA Скачать руководство пользователя страница 12

Страница: 12 / 20

Step-by-step installation guide

A. OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

. INSTALLATION PROCEDURE FOR

THE EXHAUST ADAPTOR AND

PROPER DAMPER OPERATION

CHECK

The exhaust Adaptor and Damper are

shipped assembled and attached to

the filler-upper.

. Slide the exhaust adaptor as shown in the

diagram above.

. Make sure the tape securing the damper is

removed and damper pivots easily before you

mount the microwave.

CAUTION

: You will need to make adjustments to

assure proper alignment with your house exhaust

duct after the microwave is installed.

. ADjUST THE EXHAUST ADAPTOR

After you have installed the microwave, you will

need to open the top cabinet and adjust the exhaust

adaptor so that you can connect it to the house

duct.

For Front-to-Back

Adjustment, Slide the

Exhaust Adaptor as Needed

Blower Plate

Back of

Microwave

Damper

NOTE

: You must attach the house duct to the

exhaust adaptor after installation is complete.

House Duct

House Duct

B. RECIRCULATING (NON-VENTED

DUCTLESS)

. ADAPTING THE mICROWAVE

BLOWER FOR RECIRCULATION

. Lift up the

blower plate.

. Remove and save the screws

that hold the blower plate to the

microwave.

Back of

Microwave

NOTE

: The exhaust adaptor with the damper is not

needed for recirculating models. You may want to

save them for possible future use.

. Remove the screw that holds the blower motor

and carefully pull out the blower unit. The wires

will extend far enough to allow you to adjust the

blower unit.

CAUTION

: To avoid breaking or cracking the blower

blade, do not touch the blade. Hold the outer case

of the blower when you pull it out or put it back in

place.

. Roll the blower unit 90 ° so that the fan blade

openings are facing toward the front of the

microwave.

SMH1927_XAA_DE68-04108A-01_EN_120725.indd 12

2012-07-25 �� 7:54:33

Содержание MC17J8100CS/AA





















Результаты поиска

Содержание MC17J8100CS/AA

Отзывы:

Похожие инструкции для MC17J8100CS/AA

Бренды по названию

Популярные бренды

Samsung MC17J8100CS/AA, Руководство по установке

Результаты поиска

Содержание MC17J8100CS/AA

Отзывы:

Похожие инструкции для MC17J8100CS/AA

Бренды по названию

Популярные бренды