Samsung HABANA NP-P50 Series Скачать руководство пользователя страница 103

Страница: 103 / 160

5- 16

5. Troubleshooting

◆

When booting up the computer

20. The "Invalid System Disk. Replace the Disk and then press any key" message appears.

→

This message may appear when the connected USB memory or CD media does not include

bootable data.

→

The "Reboot and Select the proper Boot device or Insert a bootable media in the selected Boot

device and press a key" message appears.

→

Check if the signal and power cables are properly connected to the hard disk drive.

→

Check if the hard disk drive is recognized in the BIOS SETUP.

→

The operating system on the hard disk drive is corrupted. Reinstall Windows.

21. The "To enter BIOS SETUP, press <F2>. To continue, press <F1>." message appears.

→

This may happen when the BIOS settings are different from the system environment. In this

case, setup the BIOS according to your system environment.

→

Press <F2> to enter the BIOS SETUP.

→

Check if the date and time are correct in the BIOS SETUP.

→

Save the settings and restart the system.

22. The 'CMOS Checksum error’ message appears.

→

This message may appear when the CMOS battery of the main board is completely discharged.

In this case, replace the battery with a new one of the same type and set up the BIOS SETUP

according to your system environment.

23. Windows boots up in safe mode.

→

This may happen when Windows was not shut down normally. Therefore, shut down the system

by selecting Start > Turn Off Computer.

→

This may happen when the system settings have been incompletely recognized.

→

Run Check Disk.

24. I cannot boot up the computer with a USB floppy drive or from USB memory.

→

Check if the diskette is bootable.

→

This may happen when the booting priority of the device is low. In this case, change the

booting priority in the BIOS SETUP.

◆

When shutting down the computer

25. The computer is not shut down

→

If Windows does not end normally, you can forcibly shut down the system by pressing the

Power button. If the power-saving feature is activated on the Power button, press the Power

button for more than 4 seconds to turn the computer off. If the computer is then turned on again,

Check Disk is automatically run.

- This document cannot be used without the authorization of Samsung -

Содержание HABANA NP-P50 Series

































































































































































Результаты поиска

Содержание HABANA NP-P50 Series

Отзывы:

Похожие инструкции для HABANA NP-P50 Series

Бренды по названию

Популярные бренды

Samsung HABANA NP-P50 Series, Руководство по обслуживанию

Результаты поиска

Содержание HABANA NP-P50 Series

Отзывы:

Похожие инструкции для HABANA NP-P50 Series

Бренды по названию

Популярные бренды