Samsung GT-E2652 Скачать руководство пользователя

Страница: 26 / 73

SAMSUNG Proprietary-Contents may change without notice

7. Level 2 Repair

7-5

This Document can not be used without Samsung's authorization

1) Assemble the KEYPAD.
2) Assemble the LCD MODULE.

（

Caution

1) Be care of damage to the LCD MODULE.

1) Assemble the TSP CONNECTOR to PBA ASS'Y.
1) Assemble PBA ASS'Y to FRONT ASS'Y.

（

Caution

1) Be care of damage the LCD MODULE and TSP FPCB.

1) Assemble the LCD CONNECTOR.

（

Caution

1) Be care of damage to the LCD MODULE.

1) Assemble the REAR CASE.

（

Caution

1) Be care of scratch and molding damage

1) Assemble the KEYPAD.
2) Assemble the LCD MODULE.

1) Assemble the TSP CONNECTOR to PBA ASS'Y.
1) Assemble PBA ASS'Y to FRONT ASS'Y.

1) Assemble the LCD CONNECTOR.

1) Assemble the REAR CASE.

Содержание GT-E2652










































































Результаты поиска

Содержание GT-E2652

Отзывы:

Похожие инструкции для GT-E2652

Бренды по названию

Популярные бренды

Samsung GT-E2652, Руководство по обслуживанию

Результаты поиска

Содержание GT-E2652

Отзывы:

Похожие инструкции для GT-E2652

Бренды по названию

Популярные бренды