background image

1

CLOTHES DRYER

Technical Information

CAUTION

All safety information must be followed as provided in Service Manual of DV431A**/XEU.

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to dryer 
before servicing, unless testing requires power.

Code No. : DC68-02365F-01

IMPORTANT SAFETY NOTICE – “For Technicians only” 

This service data sheet is intended for 

use by persons having electrical, electronic, and mechanical experience and knowledge at a level 
generally considered acceptable in the appliance repair trade. Any attempt to repair a major 
appliance may result in personal injury and property damage. The manufacturer or seller cannot 
be responsible, nor assume any liability for injury or damage of any kind arising from the use of 
this data sheet.
• 

Due to possibility of personal injury or property damage, always contact an authorized 

technician for servicing or repair of this unit.

• 

Refer to Service Manual (DV431A**/XEU) for detailed installation, operating, testing, 

troubleshooting, and disassembly instructions.

(Technical)DV431AEP-02365F-01_EN.indd   1

2012-04-27   �� 10:22:50

Содержание DV431AEP/XEU













Отзывы: