Samsung DCS Скачать руководство пользователя

Страница: 333 / 410

SAMSUNG

MMC PROGRAMS

COMBINED SYSTEMS PROGRAMMING MANUAL

FEBRUARY 2004

MMC 804 (Page 1 of 3)

MMC: 804

SYSTEM I/O PARAMETER

FOR:

ALL

SYSTEMS

Purpose:

Sets parameters for the system I/O ports to work with one of the following:

•

a personal computer (PC)

•

Station Message Detail Recording (SMDR)

•

UCD statistics report/periodic UCD information (except 408/408i)

•

Computer-Telephony—TSAPI—Interface (CTI)

System

No. of I/O Ports

DCS, CII, 816

Two ports (Ports 1 and 2)

408/408i

One port (Port 1)

DCS500

Up to five ports available on an

DCS500 with a LAN module. The fifth port is

used for internal modem control. If no LAN module is installed, three ports are
available and the third port is used for internal modem control.

DCS100

Up to three ports available on an

DCS100. Two are supplied on the MISC 1

or MISC 2 card and one on a MEM4 card.

OS500

Three ports (Ports 2, 3 and 5). Port 5 is used for internal modem control.

Use the tables below to customise I/O ports.

PARAMETER OPTIONS

Dial 0

Service

Type of Service

Dial 1

Baud Rate

Speed

Dial 2

Char Length

Character Length

Dial 3

Parity

Parity Bit

Dial 4

Retry Count

Number of Retries

Dial 5

Stop Bit

Dial 6

Wait Time

Message Wait Time

Dial 7

DSR Check

DSR Check on/off (

all systems except DCS

)

SIM Pair

No. of the station connected to the Serial Interface Module
(SIM) (

DCS systems only

)

SERVICE TYPE

Each port can be set to one of the following service types. Note that the services available depend on
the type of system being programmed. No two ports can be programmed with the same service type.

Type

Description

PC-MMC PC

application

SMDR

SMDR report (call logging)

UCD REPT

UCD report on request by the supervisor,
or daily

UCD/SMDR

Both SMDR and UCD report will be gen-
erated

CTI

Dedicated Switch Link Interface

CTI/SMDR

CTI and SMDR

CTI/UCD

CTI and UCD

CTI/S/U

CTI, SMDR and UCD

Содержание DCS



























































































































































































































































































































































































































Результаты поиска

Содержание DCS

Отзывы:

Похожие инструкции для DCS

Бренды по названию

Популярные бренды

Samsung DCS, Руководство по программированию

Результаты поиска

Содержание DCS

Отзывы:

Похожие инструкции для DCS

Бренды по названию

Популярные бренды