Samsung CS21S8MUR Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 65

background image

Alignment and Adjustments

Samsung Electronics

4-3

4-6 E

2

PROM (IC902) Replacement

1. When IC902 is replaced, all adjustment data revert to the initial values.

So, all adjustment values when servicing should be readjusted.

2. After IC902 is replaced, connect the AC power supply cord.

3. Turn the power switch ON.

4. In stand-by, warm up the TV for at least 10 seconds.

5. Power on the TV.

4-7 White Balance Adjustment

■

Equipment : Color-Analyzer (CA-100)

■

Input Signal : Pattern signal (Toshiba pattern)

1. Select STANDARD from the menu.

2. Input an 100% White pattern.

3. Enter the “Service Mode”. (Refer to “4-8 Service Mode”)

4. Warm up the TV set at least for 30 minutes.

5. Input a Toshiba pattern signal.

6. Enter the “Video Adjust1”. (Refer to table 2.)

- Adjust “Sub Contrast” so that Y (luminance) becomes 65 ft ± 3.
- Use “Red Drive” and “ Blue Drive” to adjust High-Light (x : 265, y : 265)
- Adjust “Sub Bright” so that Y (luminance) becomes 1.2ft ± 0.3.
- Use “Red Cutoff” and “Blue Cutoff” to adjust Low-Light (x : 265, y : 265).

7. Adjust CA-100 so that the final adjustment value can be fixed.

8. Use the Channel Up/Down (

▲

/

▼

) buttons to move the cursor on the adjustment modes.

9. Use the /- buttons to change the adjustment value.

«
...
14
15
16
17
18
...
»

Содержание CS21S8MUR


































































Отзывы:

Нет отзывов

Похожие инструкции для CS21S8MUR

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 40

Бренд: Yamaha Страницы: 2

Бренд: V2 Страницы: 16

Бренд: Navilock Страницы: 9

Бренд: Williams Sound Страницы: 14

Бренд: Sennheiser Страницы: 2

Бренд: F&F Страницы: 8

Бренд: RF-Link Страницы: 4

Бренд: GME Страницы: 12

Бренд: Olson Technology Страницы: 12

SV 517 RDS/BT DAB

Бренд: Majestic Страницы: 13

Бренд: Audiovox Страницы: 44

Бренд: auna multimedia Страницы: 108

Бренд: Xtrons Страницы: 12

Бренд: AUDIOropa Страницы: 88

Бренд: Teac Страницы: 47

Бренд: AirTech Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды