manualshive.com logo in svg

Samsung CLX-FIN40S, Руководство по обслуживанию

Поделиться
Скачать
Samsung CLX-FIN40S Скачать руководство пользователя страница 139

4. Troubleshooting

4-34

SAMSUNG ELECTRONICS

Service Manual
CLX-FIN40S/CLX-FIN40L

●

Code : 

H2-3641

●

Error message : 

Booklet maker Error #H2-3641. Please open/close 

door.

●

Symptom : 

Booklet maker compiler end fence stopper does not work properly.

●

Troubleshooting method :

Is the booklet maker stopper home sensor working? (Perform diagnostic routine 116-5690)
YES / NO 

Î

1. Check if the connector of the sensor is disconnected.

2. Check if the connector J4 on the booklet maker control board is disconnected.
3. Check the harness continuity and replace it if required.
4. Replace the stopper home sensor.
5. Replace the booklet maker control board.

Is the booklet maker stopper motor working? (Perform diagnostic routine 116-0350)
YES / NO 

Î

1. Check if the connector of stopper motor is disconnected.

2. Check if the connector J4 on the booklet maker control board is disconnected.
3. Check the harness continuity and replace it if required.
4. Replace the stopper motor.
5. Replace the booklet maker control board.

Is there any high load when stopper moves up and down manually?
NO / YES 

Î

1. Check if there is any dust or object on contact area. Clean them if required.   

2. Check if the stopper driving belt tension is too high. Replace timing belt if it does.

Содержание CLX-FIN40S





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды