Samsung CLX-FIN40L Скачать руководство пользователя

Страница: 15 / 148

1. Specification

1-10

SAMSUNG ELECTRONICS

Service Manual
CLX-FIN40S/CLX-FIN40L

1.6 Mode Feature

Main Stack Mode

: Must be able to receive faced-down images from the IOT and stack as much as

3,000 sheets (A4/LT 80gsm) onto the main stacker tray. The Stacker tray must be able to

accommodate various types and sizes of sheets.

Offset Mode

: Shifts the space between sets to 30mm in order to distinguish sets that have been

post-processed during Main Stack Mode.

Top Stack Mode

: The finisher must be able to assort and discharge papers to the top tray, and

stack as much as 250 sheets(80gsm). Sheets that have been collected to the Top tray cannot access

post-processing functions such as offset, stapling, punching, etc.

Staple Mode

: When the user selects this mode, it staples designated corner of the papers that have

to compiled (more than 2 pages).

. Corner staple(Front, Rear): Clinches at 45 degrees from the paper path.

. Dual staple: Clinches at 90 degree from the paper path designated according to the type of paper

In case of simplex copy, the clincher leg must face the back side of the image. The stapler must be

able to clinch as much as 50 sheets (90gsm).

Hole Punch

: The punch module should accommodate NA2/3, EU2/4, or Scandinavia 4 hole

module(TBD) depending on the target market. There must be a waste hopper that collects wastes

produced during hole punching. The waste hopper must be big enough to allow at least 5,000

punches before it becomes full.

Booklet Maker Mode :

A Dual Stapling must be possible at V-folding line of the paper (that can

cover 15 sheets, or a 216gsm cover + fourteen 80gsm sheets, etc) that goes through the Booklet

maker. The folding is positioned at the centerline of the paper path.

Содержание CLX-FIN40L





















































































































































Результаты поиска

Содержание CLX-FIN40L

Отзывы:

Похожие инструкции для CLX-FIN40L

Бренды по названию

Популярные бренды

Samsung CLX-FIN40L, Руководство по обслуживанию

Результаты поиска

Содержание CLX-FIN40L

Отзывы:

Похожие инструкции для CLX-FIN40L

Бренды по названию

Популярные бренды