Samsung CE2813NR Скачать руководство пользователя страница 15

Страница: 15 / 22

- 13 -

6. Troubleshooting

6-1 Electrical Malfunction

NOTE

Interlock monitor switch must be replaced when the fuse is blown out.

Parts

Cause

Diagnosis

Remedy

Fuse blows

out when

door is

opened.

Defective primary

interlock switch

are winding.

Check continuity of the primary switch terminals

with wire removed using a multimeter. If there is

continuity inter between switch terminals when door

is opened,the switch is defective.

Replace the primary

interlock switch

Defective interlock

monitor switch

Check continuity of the monitor switch terminals

with wire removed by using a multimeter.

If there is continuity between switch terminals

the

door is closed, the switch is defective.

Replace the interlock

monitor switch

Fuse is

Open

Layer short of the

secondary coil of

H. V. Transformer

The fuse will not blow right away, but if it blows in

a few seconds, then there is a layer short If the

fuse blows with H. V. Trans secondary open, the

transformer may be faulty.

Replace H. V.Transformer

Oven lamp

does not

light.

1) Fuse blown out

Check fuse.

Replace the fuse.

2) Poor contact of

power cord.

Check continuity of power supply cord. Also

check whether the power cord is securely wired.

Adjust or replace

the power supply cord

3) Defective lamp

The fan motor rotates, but lamp does not light.

Replace the lamp.

4) Defective timer

contacts

Check the terminals of timer for continuity,turning

the timer knob ON and OFF repeatedly.

Replace the timer.

5) Thermal cutout

S/W open

In this case the oven lamp and fan do not turn on

Replace the thermal

cutout S/W

Fan does

not operate.

1) Defective fan

motor.

If 230V is found at motor terminals, the motor

should be replaced.

Replace the motor.

2) Defective con-

tacts of timer

The oven lamp does not light and fan motor does

not operate.

Replace the timer.

WARNING FOR HIGH VOLTAGE

4000 VOLTS EXIST AT THE HIGH VOLTAGE AREA. DO NOT OPERATE THE OVEN WITH
CABINET PARTS REMOVED. DO NOT REMOVE THE CABINET PARTS IF THE POWER SUPPLY
CORD IS PLUGGED IN THE WALL OUTLET. UNPLUG THE POWER CORD BEFORE SERVICING.

Содержание CE2813NR























Результаты поиска

Содержание CE2813NR

Отзывы:

Похожие инструкции для CE2813NR

Бренды по названию

Популярные бренды

Samsung CE2813NR, Руководство по обслуживанию

Результаты поиска

Содержание CE2813NR

Отзывы:

Похожие инструкции для CE2813NR

Бренды по названию

Популярные бренды