background image

Samsung Electronics

6-3

Parts

Cause

Diagnosis

Remedy

1) Open cathode

Check the terminals with a multimeter to see

Replace magnetron.

of magnetron

if the heater circuit is open.

2) Defective

Check the H. V. Diode for continuity in the reverse and

Replace H. V. Diode.

-

H. V. Diode

normal directions using megger. If there is continuity
in the reverse direction, the H. V. Diode may be faulty.
(In this event H. V. Capacitor will be hot)

3) Shorted

Connect megger leads to quick-connect terminal &

Replace magnetron.

magnetron

body of the magnetron if there is continuity, the
magnetron may be faulty. (In this case  the main
fuse will be blown)

Food is

4) Defective

If there is a crack in the magnetron antenna (dome),

Replace magnetron.

not heated.

magnetron

the magnetron is defective.

5) Poor contact

Check if the screws are secured well to the door hinge.

Replace or adjust.

of primay

and pressing it ON and OFF repeatedly.

interlock switch

6) Open coil of

Check the continuity of primary coil and secondary

Replace the

H. V. Trans-

coil. If there is no continuity, H. V. Transformer is

H. V. Transformer.

former

defective.

7) Shorted H. V.

Check the continuity of capacitor.

Replace the

capacitor

If the capacitor shorts, the fuse blows

H. V. Capacitor.

6-2 Unsatisfactory Cooking

Symptom

Related Parts

Check Points

Remedy

Microwave

H.V.Transformer

1) Check if the primary and secondary coil is open or shorted.

Replace.

cooking does

*  Resistance of primary coil: Approx. 1.38 Ω

not work.

Resistance of secondary coil: Approx. 104.0 Ω

2) Check if the MGT Heater Voltage is approx. 3.3V AC.

Caution : High voltage !

H.V.Capacitor

Check continuity of capacitor between two

Replace.

terminals with H.V.wire lead removed.
The  resistance should be approx. 10M

, it's failure.

H.V.Diode

1) If there is no continuity in forward, direction the H.V.Diode is open.

Replace.

2) If there is continuity in reverse direction, it's shorted.

Fan motor

Fan motor

Check if the motor coil is open.

Replace.

does not rotate.

6-3 Part Check List

Troubleshooting

Содержание CE2713R























Отзывы: