manualshive.com logo in svg

Samsung CA17K Series, Руководство по обслуживанию

Поделиться
Скачать
Samsung CA17K Series Скачать руководство пользователя страница 4

3-1-1 Before making Disassembly

1. Disconnect or power cord from the monitor.
2. With a pad beneath it, stand the monitor on its

front with the screen facing downward and
the base close to you.

3-1-2 Cabinet Disassembly

1. Remove the Stand from the monitor.

(Refer to Stand manual)

2. Remove 2 screws on the Rear cover.

3. Incline the monitor by lifting the rear of the

monitor.

4. Push the Opening jig each groove along the

Side of the monitor till it makes a “ttak”
sound. (2 grooves : Left and Right, Make sure
each snap is disengaged.)

5. Pull the Rear Cover up off the monitor.

CA17K*/CA17J*

3-1

CONFIDENTIAL

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the
CA17K*/CA17J* monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use with caution when

handling these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. To remove the Rear Cover, you must use the special opening jig tool.

Figure 1

Figure 2

Figure 3

Figure 4

Содержание CA17K Series




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды