Samsung AJ NB1DEH Series Скачать руководство пользователя страница 5

5

English

Installation Pr

oc

edur

e

Installation Procedure

Step 1  Checking and preparing 

accessories

The following accessories are supplied with the indoor 
unit. The type and quantity may differ, depending on the 
specifications.

Installation template

Dimension gauge

Insulation drain

Flexible hose

Rubber

Installation manual

Cable-tie

User manual

Step 2  Choosing the installation 

location

Installation location requirements

•  There must be no obstacles near the air inlet and 

outlet.

•  Install the indoor unit on a ceiling that can support its 

weight.

•  Maintain sufficient clearance around the indoor unit.
•  Before installing the indoor unit, be sure to check 

whether the chosen location is well-drained. 

•  The indoor unit must be installed such that it is beyond 

public access and is not touchable by users.

•  Rigid wall without vibration.
•  Where it is not exposed to direct sunshine.
•  Where the air filter can be removed and cleaned easily.

  CAUTION

•  As a rule, the unit cannot be installed at a height of 

less that 2.5m.

•  If you install the cassette or duct type indoor unit on 

the ceiling with humidity over 80%, you must apply 
extra 10mm of polyethylene foam or other insulation 
with similar material on the body of the indoor unit.

Содержание AJ NB1DEH Series

































Отзывы: