Samsung AC026JNNCEH Скачать руководство пользователя страница 28

Страница: 28 / 77

Samsung Electronics

Error Mode

Cause

Measures

Product operation with error

Diagnosis method

Operation

Defrost

Timer

Filter

Outdoor Unit

compressor

Outdoor Unit

fan

indoor Unitheat

fan

Power reset

operation-off

Error of room temperature sensor in the indoor
unit (Open/Short)

• Check indoor temperature sensor connection.
• Check indoor temperature sensor’s resistance value to see if it’s short/open.

operation-off

page 4-17

Error of heat exchanger IN/OUT sensor in the
indoor unit (Open/Short)

• Check EVA IN/OUT sensor connection.
• Check EVA IN/OUT sensor’s resistance value to see if it’s short/open.

operation-off

page 4-18

Error of fan motor in the indoor unit

• Check the connection of motor connector
• Check the speed of the motor fan

operation-off

page 4-19

Error of the outdoor temperature sensor
Error of the condensor temperature sensor
Error of the discharge temperature sensor

• Check outdoor temperature sensor connection.
• Check outdoor temperature sensor’s resistance value to see if it’s short/open.

operation-off

No communication for 2 minutes between indoor
and outdoor unit (communication error for more
than 2 minutes)

• Check connection between indoor and outdoor unit communication cables

operation-off

page 4-20

Error of outdoor unit

• Check error occurred with outdoor unit.

operation-off

Detection of the float switch

• Check float switch connection.
• Check whether the drain has been filled with water.

operation-off

page 4-21

EEPROM error

• Check if there is damage with EEPROM component.

operation-off

page 4-22

EEPROM option error

• Check the indoor model to set the options.
• Inspection for match between indoor and outdoor machine models

operation-off

MDS-kit error

-.Check the wire connection
-. Check the MDS-KIT
-.Check the indoor PBA

operation-on

page 4-49

4-2 Items to check before diagnostics

4-2-1 Four directions cassette type

4-9

Blink

Off

Содержание AC026JNNCEH














































































Результаты поиска

Содержание AC026JNNCEH

Отзывы:

Samsung AC026JNNCEH, Руководство по обслуживанию, Страница: 28 / 77

Результаты поиска

Содержание AC026JNNCEH

Отзывы: