background image

Owner’s Manual

3

Important Safety Information

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings. 

Install in accordance with the 
manufacturer’s instructions.

8.  Do not install near any heat sources such 

as radiators, heat registers, stoves, or 
other apparatus (including amplifiers) 
that produce heat.

9.  Do not defeat the safety purpose of 

the polarized or grounding type plug. 
A polarized plug has two blades with 
one wider than the other. A grounding 
type plug has two blades and a third 
grounding prong. The wide blade or the 
third prong are provided for your safety. 
If the provided plug does not fit into 
your outlet, consult an electrician for 
replacement of the obsolete outlet.

10.  Protect the power cord from being walked 

on or pinched particularly at the plugs, 
convenience receptacles, and at the 
point where they exit from the apparatus.

11.  Only use attachments/accessories 

specified by the manufacturer.

12.  Use only with the cart, stand, tripod, 

bracket, or table specified by the 
manufacturer, or sold with the apparatus. 
When a cart is used, use caution when 
moving the cart/apparatus combination to 
avoid injury from tip-over.

13.  Unplug the apparatus during lightning 

storms, or when unused for long periods 
of time. 

14.  Refer all servicing to qualified personnel. 

Service is required when the apparatus 
has been damaged in any way, such as 
power supply cord or plug is damaged, 
liquid has been spilled or objects have 
fallen into the apparatus, has been 
exposed to rain or moisture, does not 
operate normally, or has been dropped.

15.  This appliance shall not be exposed to 

dripping or splashing water and no object 
filled with liquid such as vases shall be 
placed on the apparatus.

16.  Caution-to prevent electrical shock, 

match wide blade plug wide slot fully 
insert.

17.  Please keep a good ventilation 

environment around the entire unit.

18.  The direct plug-in adapter is used as 

disconnect device, the disconnect device 
shall remain readily operable.

19.  Batteries (battery pack or batteries 

installed) shall not be exposed to 
excessive heat such as sunshine, fire or 
the like.

Содержание XPDm















Отзывы: