background image

25

Specifications

SPECIFICATIONS
Rated Output power 

 

 

 

2 X 500W at 4Ω  @0.1% THD at 1KHz

   

 

 

 

 

 

1 X 1000W at 8Ω Bridged

Frequency response 

   

 

 

20Hz~20KHz+/-0.7dB@1W Output into 8Ω (AMP OUT)

 

20 Hz~20KHz+/-0.4@+4dB Output into 10kΩ (MAIN OUT,  

 

AUX OUT, AUX SEND, EFX OUT)  

Total Harmonic Distortion 

 Less than 0.06%@20Hz~20KHz, 75W output into4Ω (AMP OUT)

 

Less than 0.1%@20 Hz~20KHz+14dB output into 10KΩ

 

(MAIN OUT, AUX OUT, AUX SEND, EFX OUT)

(Average,RS+150Ω) 

HUM & Noise -124dB equivalent input noise

(with 22Hz~22KHz BPF) 

 -100dB residual output noise (MAIN OUT, MONITOR OUT, EFX OUT)

 

 -70dB (MAIN OUT, AUX OUT) Master level control at maximum, all 

channel level control at minimum.

 

 -70dB (EFX OUT) Master level control at maximum, all channel level 

controls at minimum

Maximum Voltage Gain 

99dB CH IN (MIC) to AMP OUT

 

74dB CH IN (MIC) to MAIN OUT, MONITOR OUT

 

70dB CH IN (MIC) to AUX 2 OUT

 

52.2dB CH IN (MIC) to REC OUT

 

54dB CH IN (LINE) to MAIN OUT, MONITOR OUT

 

16dB AUX IN to MAIN OUT

 

24dB TAPE IN to MAIN OUT

Crosstalk 1KHz 

70dB adjacent input, 70dB input to output

Input Channel Equalization 

Mono Channel                                                                        HIGH 

12KHz shelving (+/- 15dB Maximum)

 

 MID 

variable 100 Hz to 8kHz peaking (+/- 15dB Maximum)

 

LOW  

80Hz shelving (+/- 15dB Maximum)

Stereo Channel                                                                        HIGH  12KHz shelving (+/- 15dB Maximum)

 

 MID 

2.5KHz peaking (+/- 15dB Maximum)

 

LOW  

80Hz shelving (+/- 15dB Maximum)

Meters 

11 POINT LED METERS (-20, -15, -10, -7, -5,-3, 0, +1, +2, +4, +6dB)

Graphic Equalizer 

9 bands (63, 125, 250, 500, 1K, 2K, 4K, 8K, 16KHz)

Internal DSP Effects 

24 BIT -  10 Presets each: 00-09  Performance; 10-19 Hall Reverb, 

20-29 Plate Reverb; 30-39 Spring Reverb; 40-49 Echo; 50-59 

 Verb; 60-69  Verb; 70-79 Echo + Verb; 80-89 

Chorus; 90-99 Flange

Phantom Power 

+48V

CLIP Indicators 

Turn on: THD> 0.1%

Foot Switch 

DIGITAL EFFECT MUTE: ON/OFF

GENERAL

Power Requirement 

120V/60 Hz, 240V/50Hz (Country Specific)

Power Consumption

TXM16 

1900W, MAX.

TXM20                                                                                         2100W,MAX.

Weight 

TXM16 

42 lbs./19.5Kg

TXM20 

50.6 lbs./23.5Kg

Dimensions 

TXM16 

19 1/4” (W)x 6 1/4” (H) x 20 3/4” (D)

 

489mm (W)x 159mm(H) x 527mm (D)

TXM20 

21 1/2” (W)x 6 1/4” (H) x 21” (D)

 

622mm (W)x 159mm(H) x 533mm (D)

Specifications are subject to change without notice.

Содержание Txm16

































Отзывы: