Samson 3381 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

Samson 3381 Series Скачать руководство пользователя страница 9

EB 8084 EN

1-5

Safety instructions and measures

1.2 Notes on possible personal injury

WARNING

!

Risk of burn injuries due to hot or cold components and pipelines.

Depending on the process medium, valve components and pipelines may get very hot
or cold and cause burn injuries.

Î

Allow components and pipelines to cool down or warm up to the ambient tempera-
ture.

Î

Wear protective clothing and safety gloves.

Risk of personal injury due to residual process medium in the silencer.

While working on the silencer, residual medium can flow out of the silencer and, de

-

pending on its properties, cause personal injury, e.g. (chemical) burns.

Î

If possible, drain the process medium from all the plant sections affected and the si-
lencer.

Î

Wear protective clothing, safety gloves, respiratory protection and eye protection.

Exposure to hazardous substances poses a serious risk to health.

Certain lubricants and cleaning agents are classified as hazardous substances. These

substances have a special label and a material safety data sheet (MSDS) issued by the
manufacturer.

Î

Make sure that an MSDS is available for any hazardous substance used. If neces

-

sary, contact the manufacturer to obtain an MSDS.

Î

Inform yourself about the hazardous substances and their correct handling.

1.3 Notes on possible property damage

NOTICE

!

Risk of leakage and damage due to excessively high or low tightening torques.

Observe the specified torques when tightening bolted joints. Excessive tightening

torques lead to parts wearing out more quickly. Parts that are too loose may cause leak-
age.

Î

Observe the usual tightening torques for the corresponding bolt diameters.

«
...
7
8
9
10
11
...
»

Содержание 3381 Series

















































Отзывы:

Нет отзывов