background image

Dry Contact Relay 

 
To use your dry contact output fail relay you must connect a 9-pin D connector to the 
unit.  You must use pins one and six as is indicated on page 7 in the remote connector 
diagram. 
 

The relay is factory preset to fail in the closed position when the low output LED 
and buzzer come on.  If you wish to have the relay fail in the open position when 
the low output LED and buzzer come on, you must take the cover off the unit and 
move the jumper to the other position on J11.  J11 is located next to the relay. 

 
 

 

 

 
 
 
To change the position of the jumper, first turn the unit off and disconnect the unit from 
both the input and output power.  Next, turn the unit on for 30 seconds to discharge the 
capacitors, then turn it off again.  Turn the unit upside down and remove the four screws.  
Remove the cover and locate J11.  It will be next to the relay as is shown in the above 
diagram.  Simply move the jumper to the desired position as is shown in the above dia-
gram.  Replace the cover and re-install the four screws.  Reconnect the unit to the input 
and output power. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

5.

IMPORTANT SAFETY INSTRUCTIONS 

 

 

SAVE THESE INSTRUCTIONS

 — This manual contains important safety and operating 

instructions for the converter. 

 

ALL CONVERTERS 

 
1) CAUTION — To reduce risk of injury, charge only lead acid or sealed gel cell 
type rechargeable batteries.  Other types of batteries may burst causing per-
sonal injury and damage. 
 
2) Do not expose converter to rain or snow. 
 
3) Use of an attachment not recommended or sold by the converter manufac-
turer may result in a risk of fire, electric shock, or injury to persons. 
 
4) Do not disassemble converter; take it to a qualified serviceman when service 
or repair is required.  Incorrect reassembly may result in a risk of electric shock 
or fire. 
 
5) To reduce risk of electric shock, disconnect converter from batteries or other 
DC supply before attempting any maintenance or cleaning.  Turning off controls 
will not reduce this risk. 

 

6) CONVERTER LOCATION 
 

i) Never place converter directly above battery; gases from battery will 
corrode and damage converter. 

 

ii) Never allow battery acid to drip on converter when reading gravity or 
filling battery. 

 

7) DC CONNECTION PRECAUTIONS 

 

i) Connect and disconnect DC output connections only after setting 
converter switch to off position. 

 
 

Samlex America

 does not recommend the use of the VTC305 Series Voltage Convert-

ers in life support applications where failure or malfunction of this product can be rea-
sonably expected to cause failure of the life support device or to significantly affect its 
safety or effectiveness.  

Samlex America

 does not recommend the use of any of its 

products in direct patient care. 
 
Examples of devices considered to be life support devices are neonatal oxygen analyz-
ers, nerve stimulators (whether used for anesthesia, pain relief, or other purposes), auto-
transfusion devices, blood pumps, defibrillators, arrhythmia detectors and alarms, pace-
makers, hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incuba-
tors, ventilators for both adults and infants, anesthesia ventilators, and infusion pumps as 
well as any other devices designated as "critical" by the U.S. FDA. 
 

2. 

Содержание VTC305-12-12










Отзывы: