background image

SAMES KREMLIN

- 3 -

N° : 578.001.130-UK-1804

CAUTION!

It is forbidden to use material containing high concentrations of halogenated hydrocarbon
solvents with

aluminium

or

zinc fillers

.Non-compliance with the instructions may cause

explosion risk causing serious or fatal injury.

EQUIPMENT REQUIREMENTS

Guards (motor cover, coupling shields, connectors,…) have been designed for

a safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure

and / or property damage due to destruction, the overshadowing or the

partial or total removal of the guards.

PUMP

Before carrying out any work, it is imperative to read and clearly understand the disassembly and
reassembly instructions before servicing. The operator must understand the equipment and the
safety instructions. These instructions are available in the equipment manuals.

The air motor is designed to be mounted with a pump. Never modify any components or
couplings. When operating, please keep hands away from moving parts. Before starting up the
equipment, please read the PRESSURE RELIEF instructions. Please ensure that any relief or
drain valves fitted are in good working order.

HOSES

Keep hoses out of circulation areas, moving parts or hot surfaces,

Never expose product hoses to temperature higher than + 60°C / 140° F or lower than 0°C
/ 32° F,

Never pull or use the hoses to move the equipment,

Tighten all fittings as well as the hoses before operating the equipment,

Check the hoses regularly; change them if they are damaged,

Never exceed the maximum working pressure (MWP) indicated on the hose.

USED PRODUCTS

Considering the wide variety of products that are available and can be used in our equipment it is
impossible to check and make recommendations for

all chemical data,regarding the risks of

possible chemical attack and their long term chemical reaction

SAMES KREMLIN can not be held liable for :

compatibility of wetted parts,

risks to staff and the surroundings,

for worn or defective parts, for faulty equipment or units, or the qualitiy of final product.

It is the responsibility of the user to know and prevent any possible risks such as toxic vapours,
fires or explosions. He shall determine the risks of immediate reactions or pursuant to repeated
exposures of the staff,

SAMES KREMLIN shall not be liable for physical injuries, direct or indirect material damages
caused by the use of chemicals.

Содержание FPro S Series







































Отзывы: