background image

P3

QUALITY GUARANTEE

SAM Machinery products are guaranteed against any defects in either material or manufacture for a period of 24 

months from delivery date, provided that the equipment is properly maintained and has not been subject to abuse 

or misuse, operated incorrectly, over loaded or used for purposes other than for which the equipment is designed or 

is not maintained correctly or if fitted with other than genuine parts.

Claims are only valid when approved by the manufacturer. No person or agent is authorised to assume any 

liability. 

As the use of the equipment is outside our control we can only guarantee quality. No liability for loss, direct 

expenses incurred from the use of this equipment or from any other cause of in respect of performance etc. 

can be accepted.

Defective parts must be returned freight paid to the manufacturer or available to be inspected as directed. 

Should such parts prove to the manufacturers satisfaction to be faulty - repair of - replacement of defective parts 

shall constitute fulfillment of guarantee obligations. Parts destroyed, lost or tampered with nullify guarantee.

WARRANTY

SAM Machinery products as designed and supplied by Coombridge & Alexander Ltd are warranted against faulty 

workmanship and defective materials for a period of 24 months from date of purchase. Such warranty is subject to 

the following conditions:

1. 

That the basic maintenance (as noted in p5) is followed.

2. 

This warranty covers the repair or replacement of parts or machinery sold by Coombridge &  

Alexander Ltd and damaged as a result of faulty workmanship of materials in such part of machinery.  

It does not extend to any other loss or damage including consequential loss or damage to other  

property or persons, or damage through poor maintenance.

3. 

No responsibility will be accepted for repairs made other than by Coombridge & Alexander Ltd or its                

accredited agent and without prior authorisation by Coombridge & Alexander Ltd.

Without limiting the generality of paragraph 2. above, this warranty does not cover the following;

a. 

Losses sustained through delay in delivery

b. 

Travel expenses

c. 

Damage caused by accident, misuse or abuse

4. 

Damage to any goods which have been altered or modified by someone other than Coombridge &  

Alexander Ltd or its authorised dealers.

5. 

Procedure for recovery under warranty;

1. 

No loss or damage will be covered under warranty unless the following procedure is followed by 

 

the purchaser.

 

1.  If the purchaser is an authorised dealer -

 

 

a. 

Coombridge & Alexander Ltd must first be advised of details of the goods  

 

 

 

concerned, the loss or damage sustained and the circumstances in which the loss    

 

 

              or damage arose.

 

 

b. 

Coombridge & Alexander Ltd will then decide if such loss or damage is within the  

 

 

 

               terms of warranty and shall advise the dealer as to how the loss or damage    

 

 

 

               is to be repaired.

 

2.  If the purchase is not an authorised dealer - 

 

 

a.  

The loss or damage should be reported directly to Coombridge & Alexander Ltd  

 

 

 

      

who will advise whether it is covered by the warranty and direct the purchaser  

 

 

 

accordingly as to what action is to be taken.

Содержание TANDEM-AXLE



















Отзывы: