Sam SP Скачать руководство пользователя страница 10

Страница: 10 / 12

3DTH

4DTH

6ETH26

8GTH8

10GTH9

6ETH28

8GTH14

25.4mm-14 Esna Nut (Short)

25.4-14 Esna Nut (Short)

25.4-12 Esna Nut

125-150 ft. Ibs

125-150 it. Ibs

125-150 ft. Ibs

125-150 it. Ibs

125-150 ft. Ibs

150-175 ft. Ibs

IMPELLER NUT INSTALLATION TORQUE

Use following impeller nut torque value during installation:

NOTE: Before installing impeller onto the shaft, apply coat of Loctite grade 242 into the impeller bore to help prevent
corrosion.

TROUBLE SHOOTING

Between regular maintenance inspections, be alert for signs of motor or pump trouble. Common symptoms are listed
below. Correct any trouble immediately and AVOID COSTLY REPAIR AND SHUTDOWN.

Will not prime

Suddenly stops pumping

SP | Impeller Nut Installation Torque | Trouble Shooting

Pump Model

Nut Size

Torque Value

CAUSES

CURES

1. No liquid in pump casing.

2. Loose suction inlet and/or

suction check valve cover

plate.

3. Worn suction inlet gasket

and/or cover plate gasket.

4. Loose suction chamber drain

plug.

5. Worn pump shaft seal assy.

6. Loose clean out cover and/or

worn clean out gasket.

7. Air release line clogged.

Fill pump casing with liquid being pumped.

Tighten bolts.

Replace with new gaskets.

Tighten plug, use pipe dope or Teflon tape.

Install new seal

Replace with new gasket and tighten hand knobs.

Clean air release line.

Clogged suction line or suction

strainer.

Clean suction line and strainer.

Содержание SP













Результаты поиска

Содержание SP

Отзывы:

Sam SP, Руководство пользователя, Страница: 10 / 12

Результаты поиска

Содержание SP

Отзывы: