background image

IQDMX30/IQDMX31

Technical Specification

Issue 2 Rev 5

Page 11

© 2015 SAM

Hue Adjust

±180 in steps of 1 

Master Video Gain

±6 dB in steps of 0.1 dB

Y-Gain

±6 dB in steps of 0.1 dB

Cb/Cr Gain

±6 dB in steps of 0.1 dB

Y/C Timing

±8 pixels in 2 pixel steps (SD)

±16 pixels in 2 pixel steps (HD/3G)

Picture Position

±8 pixels in 2 pixel steps (SD)

±16 pixels in 2 pixel steps (HD/3G)

Pattern On

On/Off

Pattern Select

75% Color Bars, Black

Caption On

On/Off

Edit Caption

19 characters available

Audio Controls

Embedder Assignment

Group 1 to 4 Enable

On/Off

Pair 1 to 8 Source L / Non-PCM

Dis-embed 1_1 to 8_2, AES 1 to 8, Tone, Silence

Pair 1 to 8 Source R

Dis-embed 1_1 to 8_2, AES 1 to 8, Tone, Silence

Pair 1 to 8 Stereo

Link channel pairs

Pair 1 to 8 Polarity L/R

On/Off

Pair 1 to 8 Gain L/R

+12 dB to -72 dB in 0.1 dB steps

Pair 1 to 8 Non-PCM

On/Off

AES Assignment

AES 1 to 8 (4) Source L / Non-PCM

Dis-embed 1_1 to 8_2, Tone, Silence

AES 1 to 8 (4) Source R

Dis-embed 1_1 to 8_2, Tone, Silence

AES 1 to 8 (4) Stereo

Link channel pairs

AES 1 to 8 (4) Polarity L/R

On/Off

AES 1 to 8 (4) Gain L/R

+12 dB to -72 dB in 0.1 dB steps

AES 1 to 8 (4) Non-PCM

On/Off

Processed Audio Delay Control

Coarse Manual Delay

Up to 1.75 s in 5 ms steps

Fine Manual Delay

± 0.25 s in 0.5 ms steps

Tone

Frequency L/R

100 Hz to 10 kHz in 100 Hz steps

Channel Ident

On/Off

HANC Data

Blank HANC (Removes all HANC data. Note audio removed when embedders 
disabled)

Audio Monitoring

Silence Detect

0 to -80 dB in steps of 1 dB

Signal Overload Detect

0 to -80 dB in steps of 1 dB

Warning Timer

1 to 20 seconds in steps of 1 second

Other Controls

Содержание IQDMX30-3G










































Отзывы: