2
3
Enter MENU and scroll down
until you will find the “TEST
LINK” option. Press TICK
button to continue.
Now your thermostat is
sending a TEST message to the
receiver with the expectation
of receiving a response. While
testing, both red and green
LED will be intermittently
flashing.
Your thermostat will indicate
that the connection has been
tested successfully and will
return to normal operation.
1
In this mode, the user can set the schedules for the thermostat (temperature setpoints
for specific periods of time). Programmed schedules should use all time periods.
1
To access this option, press the
MENU button once and then
press TICK to confirm.
1b
1a
1c
Using UP or DOWN, select the
program type between:
5
&
2.
All
(set one schedule for
the entire week)
Individual
(set a daily
schedule). Press TICK to
confirm.
Using UP or DOWN, set the
hour and then press TICK,
which will then move to
minutes, that can be changed
in the same way.
1e
Using UP or DOWN, set the
temperature and then press
TICK to confirm. Repeat this
process for all 6 programs.
1d
2
3
You can boost heating for up
to 9 hours. Only available in
AUTO and FROST mode.
Can choose:
AUTO - follow schedule
ON 24/7 - MANUAL
OFF (FROST MODE)
To access the following option,
you need to press the MENU
button and go DOWN until you
see OPERATING MODE and press
TICK to enter the OPERATING
MODE menu. To access the
BOOST HOURS menu, follow the
same steps as shown above.
4
5
Press MENU, navigate DOWN
until you see the HOLIDAY
menu and then press TICK
to CREATE/EDIT HOLIDAY.
HOLIDAY MODE is a program
that will use FROST TEMP for
the selected period when you
are going away on holiday.
Also, in this menu you can
cancel a previously set up
holiday and go back to normal
operating mode. To cancel
holiday, press TICK to confirm.
This is an example for your weekly
schedule. High temperature should
be used for the ON times and low
temperature for the OFF times.
TIME:
TEMPERATURE:
06.00
21 °C
10.00
14 °C
12.00
21 °C
14.00
14 °C
18.00
21 °C
21.00
14 °C
6
Press MENU, then using
DOWN, navigate until you
see the Advanced Settings
submenu and press TICK.
For more details about this
submenu, please check the
Installer’s Guide.
7
Press the MENU button, then press the UP button and the TICK
button to set your language. ENGLISH is the default language but
it can be changed by using UP or DOWN and navigate through the
language options, then press TICK to select and confirm.
MENU /
GRAB
TOP
AND
BOTTOM
TO OPEN
FACTORY RESET will require PIN code if locked.
Press and hold UP and DOWN arrow
keys for 5 seconds. Select YES to
perform Factory Reset and confirm
with TICK Key.
The thermostat will now restart itself
restoring factory settings. You may now
proceed with initial configuration of the
thermostat.
2
1
For overriding the schedule to bring the HEAT on, use
the UP button to increase the temperature and press
TICK to confirm.
1
This setting will be valid until the next
scheduled program.
WQ610RF: Testing Link
Programming - AUTO Mode
Temporary Manual Override
Factory Reset
Additional installation notes for WQ610:
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK
E: [email protected]
E: [email protected]
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change
specification, design and materials of products listed in this brochure without prior notice.
www.salus-controls.com
Issue Date: Nov 2019
V005
For PDF Installation guide please go to
www.salus-manuals.com
