manualshive.com logo in svg

Salford I-1100, Сборка и каталог запасных частей, Страница: 68 / 74

Поделиться
Скачать
Salford I-1100 Скачать руководство пользователя страница 68

Salford Group Inc.

Page 68

12-2015

MNP870-32-35-16A 2016 870-32ft & 35ft Assembly and Parts Manual Rev A

Do not connect the cylinder rod until system has been charged with oil.

1. Prop up the cylinder with a block of wood (fig 1). Check to see that the

 rod will extend completely without striking anything.

2. Connect tractor

(note: check to see that all cylinders extend and retract in sync.  

If one goes backwards, check the plumbing.)

3. Extend cylinders completely, hold lever for 30 sec. as air exits cylinder.

4. Retract cylinder completely, hold lever for 30 sec. as air exits.

5. Repeat steps 3&4 three times.

6. Install cylinder pins.  Be sure washers are installed correctly (see fold

cylinder parts page).

Air in the wing cylinder will cause wings to fall to the ground!!!

Whenever air could have entered the cylinders, repeat the process above to

purge circuit.

ALWAYS UNFOLD WINGS before working on hydraulics!!!  

Never  work on a lift

system with the wings folded

Fig 1.  When charging the circuit, prop up

cylinder with block of wood.  Be sure the

rod can extend freely without striking 

anything.

CHARGING FOLD CYLINDERS

HOSE

HARDWARE

ITEM QTY

PART NO.

DESCRIPTION

A

4

HS3536

3 1/2 BORE x 36" STROKE HYD. CYLINDER

B

2

H80104P

1/2" NPT PIONEER COUPLER

C

2

H915086

NIPPLE -08ORB TO -06M NPT

D

6

H956666

TEE -06F NPT ALL SWIVEL

E

6

H951586

ELBOW -08 ORB TO -06F SWIVEL NPT

F

2

H1404668

0.08 RESTRICTOR -06M NPT TO -06F SWIVEL

G

1

HG-PT24E24R21R

PAIR OF GREEN EXTEND / GREEN GREY 

RETRACT PLASTIC HOSE GRIPS

LABEL QTY. LENGTH ft-in [cm]

FROM

TO

32ft

35ft

8

1 15' 6" [472] 15' 6" [472]

TRACTOR

TEE

9

1 15' 6" [472] 15' 6" [472]

TRACTOR

TEE

10

4

22' [671] 23' 6" [716] FRONT CYLINDER TEES REAR CYLINDERS

11

2

3' [91]

4' 6" [137]

TEE

FRONT BARREL TEE

12

2

3' [91]

3' 10" [117]

TEE

RH FRONT ROD TEE

RH FRONT ROD TEE

RH FRONT ROD

13

2

2' 6" [76] 3' 6" [107]

TEE

LH FRONT ROD TEE

LH FRONT ROD TEE

LH FRONT ROD

B

B

C

D

A

D

E

9

A

A

E

E

E

E

12

13

12

13

11

10

10

8

9

11

11

12

13

F

D

F

D

8

11

11

13

12

10

10

Install rod end  fittings pointing  DOWN to prevent  interference with  wing hinges

G

G

ROUTE HOSES ALONG FRAME CLAMP WHERE PROVIDED

Wing Fold Hydraulics

Return to Contents

Содержание I-1100











































































Отзывы:

Нет отзывов