background image

F G - 3 6   P A R T S   L I S T  

19

SAITO FG-36 PARTS LIST

deScRIPTIOn 

QTy 

deScRIPTIOn 

QTy

01 

Cylinder (left) 

42 

Rocker arm screw and nut (42-1,42-2) 

2ea

06 

Piston 

43 

Rocker arm pin 

2

07 

Piston pin 

44 

Rocker arm bracket (left) 

1

08  

Piston pin retainar 

45 

Rocker arm bracket (right) 

1

09 

Piston ring 

46 

Valve (in and out) (46-1, 46-2) 

2

10 

Connecting rod 

47 

Valve Retainer (47-1,47-2,48) 

2ea

14 

Cylinder screw set (14-1, 14-2, 14-3, 14-4) 

1set 

48 

Valve retainer (Cotter) 

4

15 

Crankcase 

49 

Rocker arm cover 

2

17 

Rear cover 

69 

Intake manifold 

1

19 

Breather nipple 

74 

Muffler 

1

20A 

Front bearing 

75 

Muffler manifold (75-1, 80) 

1

22 

Rear bearing 

80 

Muffler nut 

2

23 

Crankshaft 

82-1  Carburetor complete 

1set

27A 

Taper collet and drive flange (27-1, 27-2) 

1ea 

83-1

  Carburetor body assembly 

1set

28 

Prop washer and nut (28-1,28-2) 

1ea 

 

82-1-1, 82-1-2, 82-1-3, 82-1-4, 82-1-5 

 

31 

Crankcase screw set (31-1, 31-2, 31-3) 

1set 

90

 

Carburetor screw and spring set 

1set

 

32 

Engine gasket set (32-1, 32-2, 32-3, 32-4) 

1set 

 

82-1-9, 82-1-10, 82-1-11, 82-1-12 

33 

Cam gear housing 

91 

Carburetor gasket set (82-1-6, 82-1-7, 82-1-8) 

1set

35 

Cam gear 

93 

Intake velocity stack 

1

36A 

Cam gear shaft 

95 

Engine mount set (95-1, 95-2, 95-3, 95-4, 95-5) 

1set

37 

Steel and washer set (37-1, 37-2) 

1set 

110  Anti loosening nut 

1

38 

Tappet 

149  Oil slinger 

1

39 

Pushrod 

152  Screw-pin (for drive flange setting) 

1

40 

Pushrod cover and rubber seal (40-1, 40-2, 40-3) 

2ea 

153  Electronic ignition system 

1set

41 

Rocker arm 

 

153-1, 153-2, 153-3, 153-4

OUTSIDE DIMENSIONS (mm)

SPECIFICATIONS

Disp: 36.3cc (2.20 cu in)
Bore: 38mm (1.49 in)
Stroke: 32mm (1.26 in)
Weight: (Engine only) 48.2 oz 
(1252 g)
Weight: (Muffler only) 3.0 oz 
(86 g)
Weight: (Engine Mount only) 9.6 oz 
(270 g)
Weight: (Ignition only) 5.4 oz 
(152 g)
Total weight with motor mount, 
muffler and ignition system: 66.2 oz 
(1760 g)
Crankshaft: M8x1.25
Cylinder: AAC
HP: 3.5 approximately
Fuel Efficiency: 30cc/minute
Propeller Size: Dia. 18–19 x Pitch 
8–9; Dia. 20x Pitch 8

Benchmark Propeller: APC 18x6W @ 
8,300 rpm
RPM Range: 1,700–9,000 rpm 
Fuel Consumption: Approximately 
30cc/minute at full throttle and 
approximately 7,500 rpm.  Fuel 
consumption will depend on the load 
of the propeller. During actual flight, 
fuel consumption increases slightly.
Electrical usage of ignition system: 
Approximately 200mAh for 15 
minutes.
Fuel: Gasoline-Oil mix of 20:1 (20:1 
is recommended for break in and 
continuous operation).
Oil:  The use of only 100% synthetic 
oil is such as our Evolution Oil 
(EVOX1001Q)

18 

F G - 3 6   D I M E N S I O N S   A N D   S P E C I F I C A T I O N S

14387 SAI FG_20andFG_36 Manual.indd   18-19

12/16/08   2:09:15 PM

Содержание 2008 FG-20















Отзывы: