background image

Operation

10

Using Dual watch (requires priority channel is programmed)

To activate

 Dual watch, press the 

SCN

 key.

The display shows “

Dual

” at the top and “

D

” at the bottom right. 

The radio toggles between the selected channel and channel D (if 
channel D is programmed as the priority channel).

To terminate 

Dual watch, press 

SCN

 again.

Scanning channels

To activate

 scanning memory, press 2 times 

SCN

 within ½ a second. 

During scanning, the display shows “

SC

” in the channel field. The 

radio toggles between channel D and each of the channels are 
marked for scanning (only if a priority channel, e.g. D was 
programmed).

To terminate

 scanning, press 

SCN

 once.

Changing the transmitter power

To change

 the transmitter power, press the 

Hi/Lo

 key. The display shows 

Lo

” when power is set to low. Otherwise maximum power is used.

Locking the keypad

To lock

 the keypad, press and hold the 

Light/Lock

 button. The display 

shows a key symbol when the keypad is locked.

To unlock

 the keypad, press and hold the 

Light/Lock

 button again.

0740

Содержание SP3550





















































Отзывы: