Sailor 6215 VHF DSC Скачать руководство пользователя страница 38

Страница: 38 / 104

Chapter 2: Operation

DSC calls

Power failure while in distress

In case of a power failure or switch-off during the
transmission of a Distress the SAILOR 6215 VHF DSC
gives an audible warning after power-up and
automatically resumes sending Distress 10 seconds
after power up.

Within the 10 seconds you have the following options:

•

Press

QUIT

to terminate the active distress procedure (acknowledged or

unacknowledged)

•

Press

CONFIRM

(or do nothing) to resume the sending Distress procedure.

Receiving distress calls

When the radio receives a distress call, the 2-tone alarm sounds.

Types of distress calls are DISTRESS, DISTRESS ACK,
DISTRESS RELAY and DISTR. RELAY ACK.

1. To switch off the 2-tone alarm press the soft key

SILENT

. A press on

any other key

also switches off

the 2-tone alarm.

2. If you decide to stay in the communication loop to

receive follow up information, updates etc., press
the soft key

3. If you don’t accept the distress call, press the soft

key

CANCEL

, then the radio logs the call.

4. Monitor channel 16 as a coast station may require

your assistance. If the radio is not on channel 16, turn the
selector wheel knob or use the key

16/C

to go to channel 16.

5. The radio receives the first distress acknowledgement call and

the 2-tone alarm sounds again. To switch off the 2-tone alarm press the
soft key

SILENT

. A press on

any other key

also switches off the 2-tone

alarm.any key.

Содержание 6215 VHF DSC









































































































Результаты поиска

Содержание 6215 VHF DSC

Отзывы:

Sailor 6215 VHF DSC, Руководство пользователя и инструкция по установке, Страница: 38 / 104

Результаты поиска

Содержание 6215 VHF DSC

Отзывы: