V2.0 2021 Copyright Safewaze
Page 13
LOAD IN
DICATO
R
LOA
D IN
DIC
ATO
R
A
FALL-ARREST
ANSI Z359.14, ANSI A10.32
OSHA 1910.66, OSHA 1926.502
020053
ANSI Z359.14,
ANSI A10.32
OSHA 1910.66, O
SHA 1926.5
02
020053
4.0 INSTALLATION
4.1 PLANNING
Plan your fall protection system before starting your work. Account for all factors that may affect your safety before, during, and after a fall. Consider all
requirements and limitations defined in Section 2.
4.2 HARNESS MOUNTING WITH BEHIND THE WEB BRACKET
The Behind the Web Bracket comes fully assembled and ready for installation. No tools are required for installation of the bracket onto harness. Use
the following instructions and Figure 15 to install the bracket:
To Fasten To Harness:
1. Unfasten the two small brackets on the green retractable spacer off of the carabiner.
2. Slide the green spacer around to the side of carabiner to allow opening of the carabiner gate.
3. Open the carabiner gate and slide spacer off of carabiner and remove one of the retractables.
4. Holding gate open on carabiner, insert the open end of carabiner through the webbing loops at Dorsal D-ring on the X Pad of harness.
Ensure that both loops of webbing on X Pad are inside of carabiner.
5. With carabiner gate still open, slide the removed retractable and green spacer back onto carabiner and allow carabiner gate to close.
6. Slide the green retractable spacer back over the gate of carabiner and snap the two small brackets back into place on carabiner, with the
web loops positioned between these two small brackets.
FIGURE 15 - BEHIND THE WEB BRACKET INSTALLATION
Bracket
Bracket
LOAD IN
DICATO
R
LOA
D IN
DIC
ATO
R
A
FALL-ARREST
ANSI Z359.14, ANSI A10.32
OSHA 1910.66, OSHA 1926.502
020053
ANSI Z359.14,
ANSI A10.32
OSHA 1910.66, OSHA
1926.502
020053
4.3 HARNESS MOUNTING WITH SW-9012 BEHIND THE WEB BRACKET
The D-ring brackets comes fully assembled and ready for installation. No tools are required for installation of the bracket onto harness. Use the
following instructions and Figure 16 to install the SW-9012 Behind the Web Bracket. Figure 17 illustrates the Carabiner w/Dual Bracket which simply
utilizes a double locking carabiner to attach the bracket to the Dorsal D-ring of the harness:
To Fasten To Harness:
1.
Ensure that the curved portion of SW-9012 is in a downward orientation relative to the harness (See Dwg. 1, Figure 16).
2. Simultaneously depress both locking buttons (A) and (B) (See Dwg. 2, Figure 16) and slide the bracket open as indicated
(See Dwg. 3, Figure 16).
3. With the bracket open, install dual leg retractables onto the bracket via the swivel tops of each. Swivels should be hanging on the curved
portion of bracket.
4. While pressing in on locking button (A) slide the bar behind both loops of webbing at dorsal D-ring until the bar locks back into place.
5. Check the locking function of the bracket by attempting to slide the bracket open WITHOUT depressing locking buttons (A) or (B).
Bracket bar should not move and the bracket is now locked into place.
FIGURE 16 - SW-9012 DUAL BRACKET INSTALLATION
Curved Portion
of SW-9012
Bar assembly of bracket which inserts
behind webbing at dorsal D-ring
Dwg. 1
Locking Button (B)
Locking Button (A)
Dwg. 2
Diagram of SW-9012 in opened
configuration
Dwg. 3
Dwg. 4
